Autor |
Sõnum |
Huck
Pingviini aktivist
Vanus: 41
Liitunud: 20.10.2005
Postitused: 135
Asukoht: Tln-Kur
Distributsioon: Ubuntu 9.04
|
|
Nii, esiteks tuleb tunnistada enda rumalust antud teemas ning seepärast küsida nõu targematelt
Probleem selles, et kettaruumi oleks juurde vaja- praegune 80gb win+ubuntu dualboot ei mängi välja kuidagi.
Algandmed on sellised:
Hetkel ketas:
Seagate Barracuda 7200.7 80GB Ultra ATA/100 7200RPM Hard Drive (ST380011A)
Emaplaat:
Epox EP-4PLAI
Küsimused on konkreetsed:
1. Millist kõvaketast peaks otsima üldse- ata/sata/ jne? Kui hetkel on ata siis kas see tähendab, et sobivad kõik ata tüüpi? ehk siis Parallel ATA (ATA/100, ATA133)?
2. Kas uue ketta lisamine süsteemi on niisama lihtne, et juhtmed külge ning korras. Kas toitega ei teki probleeme?
Hind võiks jämedalt alla tuhande raha jääda(mida vähem seda parem muidugi ). Täpne maht pole nii oluline. Antud hinna sisse jäävad kuni 320Gb vist.
Kui see aitab siis ka lshw ja dmidecode väljundid:
Tsitaat: |
karl-desktop
description: Desktop Computer
product: PROD00000000
vendor: OEM00000
width: 32 bits
capabilities: smbios-2.2 dmi-2.2 smp-1.4 smp
configuration: boot=normal chassis=desktop cpus=1
*-core
description: Motherboard
product: Breeds Hill
physical id: 0
*-firmware
description: BIOS
vendor: Phoenix Technologies, LTD
physical id: 0
version: 6.00 PG (06/24/2004)
size: 128KiB
capacity: 192KiB
capabilities: isa pci pnp apm upgrade shadowing cdboot bootselect socketedrom edd int13floppy360 int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb agp ls120boot zipboot
*-cpu
description: CPU
product: Intel(R) Pentium(R) 4 CPU 3.00GHz
vendor: Intel Corp.
physical id: 4
bus info: cpu@0
version: 15.3.3
serial: 0000-0F33-0000-0000-0000-0000
slot: Socket 478
size: 3GHz
capacity: 3066MHz
width: 32 bits
clock: 200MHz
capabilities: boot fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe constant_tsc pebs bts pni monitor ds_cpl cid
configuration: id=0
*-cache:0
description: L1 cache
physical id: a
slot: Internal Cache
size: 32KiB
capacity: 32KiB
capabilities: synchronous internal write-back
*-cache:1
description: L2 cache
physical id: b
slot: External Cache
size: 1MiB
capacity: 1MiB
capabilities: synchronous external write-back
*-logicalcpu:0
description: Logical CPU
physical id: 0.1
width: 32 bits
capabilities: logical
*-logicalcpu:1
description: Logical CPU
physical id: 0.2
width: 32 bits
capabilities: logical
*-memory
description: System Memory
physical id: 1c
slot: System board or motherboard
size: 1280MiB
*-bank:0
description: DIMM SDRAM Synchronous
physical id: 0
slot: A0
size: 256MiB
width: 64 bits
*-bank:1
description: DIMM SDRAM Synchronous
physical id: 1
slot: A1
size: 1GiB
width: 64 bits
*-bank:2
description: DIMM [empty]
physical id: 2
slot: A2
*-bank:3
description: DIMM [empty]
physical id: 3
slot: A3
*-pci
description: Host bridge
product: 82865G/PE/P DRAM Controller/Host-Hub Interface
vendor: Intel Corporation
physical id: 100
bus info: pci@0000:00:00.0
version: 02
width: 32 bits
clock: 33MHz
configuration: driver=agpgart-intel module=intel_agp
*-pci:0
description: PCI bridge
product: 82865G/PE/P PCI to AGP Controller
vendor: Intel Corporation
physical id: 1
bus info: pci@0000:00:01.0
version: 02
width: 32 bits
clock: 66MHz
capabilities: pci normal_decode bus_master
*-display:0
description: VGA compatible controller
product: RV350 AS [Radeon 9550]
vendor: ATI Technologies Inc
physical id: 0
bus info: pci@0000:01:00.0
version: 00
width: 32 bits
clock: 66MHz
capabilities: agp agp-3.0 pm vga_controller bus_master cap_list
configuration: driver=fglrx_pci latency=255 mingnt=8 module=fglrx
*-display:1 UNCLAIMED
description: Display controller
product: RV350 AS [Radeon 9550] (Secondary)
vendor: ATI Technologies Inc
physical id: 0.1
bus info: pci@0000:01:00.1
version: 00
width: 32 bits
clock: 66MHz
capabilities: pm cap_list
configuration: latency=32 mingnt=8
*-usb:0
description: USB Controller
product: 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1
vendor: Intel Corporation
physical id: 1d
bus info: pci@0000:00:1d.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration: driver=uhci_hcd latency=0 module=uhci_hcd
*-usb:1
description: USB Controller
product: 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2
vendor: Intel Corporation
physical id: 1d.1
bus info: pci@0000:00:1d.1
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration: driver=uhci_hcd latency=0 module=uhci_hcd
*-usb:2
description: USB Controller
product: 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3
vendor: Intel Corporation
physical id: 1d.2
bus info: pci@0000:00:1d.2
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration: driver=uhci_hcd latency=0 module=uhci_hcd
*-usb:3
description: USB Controller
product: 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4
vendor: Intel Corporation
physical id: 1d.3
bus info: pci@0000:00:1d.3
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration: driver=uhci_hcd latency=0 module=uhci_hcd
*-usb:4
description: USB Controller
product: 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller
vendor: Intel Corporation
physical id: 1d.7
bus info: pci@0000:00:1d.7
version: 02
width: 32 bits
clock: 33MHz
capabilities: pm ehci bus_master cap_list
configuration: driver=ehci_hcd latency=0 module=ehci_hcd
*-pci:1
description: PCI bridge
product: 82801 PCI Bridge
vendor: Intel Corporation
physical id: 1e
bus info: pci@0000:00:1e.0
version: c2
width: 32 bits
clock: 33MHz
capabilities: pci normal_decode bus_master
*-network
description: Ethernet interface
product: RTL-8139/8139C/8139C+
vendor: Realtek Semiconductor Co., Ltd.
physical id: 5
bus info: pci@0000:02:05.0
logical name: eth0
version: 10
serial: 00:04:61:63:9f:ac
size: 100MB/s
capacity: 100MB/s
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=full ip=82.131.113.29 latency=32 link=yes maxlatency=64 mingnt=32 module=8139too multicast=yes port=MII speed=100MB/s
*-isa
description: ISA bridge
product: 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge
vendor: Intel Corporation
physical id: 1f
bus info: pci@0000:00:1f.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: isa bus_master
configuration: latency=0
*-ide
description: IDE interface
product: 82801EB/ER (ICH5/ICH5R) IDE Controller
vendor: Intel Corporation
physical id: 1f.1
bus info: pci@0000:00:1f.1
logical name: scsi0
logical name: scsi1
version: 02
width: 32 bits
clock: 33MHz
capabilities: ide bus_master emulated
configuration: driver=ata_piix latency=0 module=ata_piix
*-disk
description: ATA Disk
product: ST380011A
vendor: Seagate
physical id: 0
bus info: scsi@0:0.0.0
logical name: /dev/sda
version: 3.06
serial: 5JV9HMEY
size: 74GiB (80GB)
capabilities: partitioned partitioned:dos
configuration: ansiversion=5 signature=84fe84fe
*-volume:0
description: Windows NTFS volume
physical id: 1
bus info: scsi@0:0.0.0,1
logical name: /dev/sda1
version: 3.1
serial: 0a34e440-fc7a-3f4d-a361-21b3c05771c6
size: 29GiB
capacity: 29GiB
capabilities: primary bootable ntfs initialized
configuration: clustersize=4096 created=2008-01-13 14:10:32 filesystem=ntfs modified_by_chkdsk=true mounted_on_nt4=true resize_log_file=true state=dirty upgrade_on_mount=true
*-volume:1
description: EXT3 volume
vendor: Linux
physical id: 2
bus info: scsi@0:0.0.0,2
logical name: /dev/sda2
logical name: /
logical name: /dev/.static/dev
version: 1.0
serial: c51c3c31-5ada-4eeb-805e-e6d63056ed3b
size: 6110MiB
capacity: 6110MiB
capabilities: primary journaled extended_attributes large_files huge_files recover ext3 ext2 initialized
configuration: created=2009-01-24 13:54:29 filesystem=ext3 modified=2009-04-01 08:35:48 mount.fstype=ext3 mount.options=rw,relatime,errors=remount-ro,data=ordered mounted=2009-04-01 08:35:48 state=mounted
*-volume:2
description: EXT3 volume
vendor: Linux
physical id: 3
bus info: scsi@0:0.0.0,3
logical name: /dev/sda3
logical name: /home
version: 1.0
serial: 6265711e-520f-418c-829d-ee22ab2a3752
size: 37GiB
capacity: 37GiB
capabilities: primary journaled extended_attributes large_files huge_files recover ext3 ext2 initialized
configuration: created=2007-05-01 13:25:06 filesystem=ext3 modified=2009-04-01 08:38:05 mount.fstype=ext3 mount.options=rw,relatime,data=ordered mounted=2009-04-01 08:38:05 state=mounted
*-volume:3
description: Extended partition
physical id: 4
bus info: scsi@0:0.0.0,4
logical name: /dev/sda4
size: 1019MiB
capacity: 1019MiB
capabilities: primary extended partitioned partitioned:extended
*-logicalvolume
description: Linux swap / Solaris partition
physical id: 5
logical name: /dev/sda5
capacity: 1019MiB
capabilities: nofs
*-cdrom:0
description: DVD reader
product: RW/DVD GCC-4520B
vendor: HL-DT-ST
physical id: 1
bus info: scsi@1:0.0.0
logical name: /dev/cdrom1
logical name: /dev/dvd1
logical name: /dev/scd0
logical name: /dev/sr0
version: 1.00
capabilities: removable audio cd-r cd-rw dvd
configuration: ansiversion=5 status=open
*-cdrom:1
description: DVD writer
product: DVD_RW ND-3500AG
vendor: _NEC
physical id: 0.1.0
bus info: scsi@1:0.1.0
logical name: /dev/cdrom
logical name: /dev/dvd
logical name: /dev/scd1
logical name: /dev/sr1
version: 2.1B
serial: [_NEC DVD_RW ND-3500AG2.1B06022300
capabilities: removable audio cd-r cd-rw dvd dvd-r
configuration: ansiversion=5 status=open
*-serial UNCLAIMED
description: SMBus
product: 82801EB/ER (ICH5/ICH5R) SMBus Controller
vendor: Intel Corporation
physical id: 1f.3
bus info: pci@0000:00:1f.3
version: 02
width: 32 bits
clock: 33MHz
configuration: latency=0
*-multimedia
description: Multimedia audio controller
product: 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller
vendor: Intel Corporation
physical id: 1f.5
bus info: pci@0000:00:1f.5
version: 02
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list
configuration: driver=Intel ICH latency=0 module=snd_intel8x0
|
Tsitaat: |
# dmidecode 2.9
SMBIOS 2.2 present.
40 structures occupying 1013 bytes.
Table at 0x000F0000.
Handle 0x0000, DMI type 0, 19 bytes
BIOS Information
Vendor: Phoenix Technologies, LTD
Version: 6.00 PG
Release Date: 06/24/2004
Address: 0xE0000
Runtime Size: 128 kB
ROM Size: 256 kB
Characteristics:
ISA is supported
PCI is supported
PNP is supported
APM is supported
BIOS is upgradeable
BIOS shadowing is allowed
Boot from CD is supported
Selectable boot is supported
BIOS ROM is socketed
EDD is supported
5.25"/360 KB floppy services are supported (int 13h)
5.25"/1.2 MB floppy services are supported (int 13h)
3.5"/720 KB floppy services are supported (int 13h)
3.5"/2.88 MB floppy services are supported (int 13h)
Print screen service is supported (int 5h)
8042 keyboard services are supported (int 9h)
Serial services are supported (int 14h)
Printer services are supported (int 17h)
CGA/mono video services are supported (int 10h)
ACPI is supported
USB legacy is supported
AGP is supported
LS-120 boot is supported
ATAPI Zip drive boot is supported
Handle 0x0001, DMI type 1, 25 bytes
System Information
Manufacturer:
Product Name:
Version:
Serial Number:
UUID: Not Present
Wake-up Type: Power Switch
Handle 0x0002, DMI type 2, 8 bytes
Base Board Information
Manufacturer:
Product Name: Breeds Hill
Version:
Serial Number:
Handle 0x0003, DMI type 3, 13 bytes
Chassis Information
Manufacturer:
Type: Desktop
Lock: Not Present
Version:
Serial Number:
Asset Tag:
Boot-up State: Unknown
Power Supply State: Unknown
Thermal State: Unknown
Security Status: Unknown
Handle 0x0004, DMI type 4, 32 bytes
Processor Information
Socket Designation: Socket 478
Type: Central Processor
Family: Pentium 4
Manufacturer: Intel
ID: 33 0F 00 00 FF FB EB BF
Signature: Type 0, Family 15, Model 3, Stepping 3
Flags:
FPU (Floating-point unit on-chip)
VME (Virtual mode extension)
DE (Debugging extension)
PSE (Page size extension)
TSC (Time stamp counter)
MSR (Model specific registers)
PAE (Physical address extension)
MCE (Machine check exception)
CX8 (CMPXCHG8 instruction supported)
APIC (On-chip APIC hardware supported)
SEP (Fast system call)
MTRR (Memory type range registers)
PGE (Page global enable)
MCA (Machine check architecture)
CMOV (Conditional move instruction supported)
PAT (Page attribute table)
PSE-36 (36-bit page size extension)
CLFSH (CLFLUSH instruction supported)
DS (Debug store)
ACPI (ACPI supported)
MMX (MMX technology supported)
FXSR (Fast floating-point save and restore)
SSE (Streaming SIMD extensions)
SSE2 (Streaming SIMD extensions 2)
SS (Self-snoop)
HTT (Hyper-threading technology)
TM (Thermal monitor supported)
PBE (Pending break enabled)
Version: Intel(R) Pentium(R) 4 CPU
Voltage: 1.4 V
External Clock: 200 MHz
Max Speed: 3066 MHz
Current Speed: 3000 MHz
Status: Populated, Enabled
Upgrade: ZIF Socket
L1 Cache Handle: 0x000A
L2 Cache Handle: 0x000B
L3 Cache Handle: No L3 Cache
Handle 0x0005, DMI type 5, 24 bytes
Memory Controller Information
Error Detecting Method: 8-bit Parity
Error Correcting Capabilities:
None
Supported Interleave: One-way Interleave
Current Interleave: One-way Interleave
Maximum Memory Module Size: 1024 MB
Maximum Total Memory Size: 4096 MB
Supported Speeds:
Other
Supported Memory Types:
Other
Memory Module Voltage: 5.0 V
Associated Memory Slots: 4
0x0006
0x0007
0x0008
0x0009
Enabled Error Correcting Capabilities:
None
Handle 0x0006, DMI type 6, 12 bytes
Memory Module Information
Socket Designation: A0
Bank Connections: 0
Current Speed: Unknown
Type: Other
Installed Size: 256 MB (Single-bank Connection)
Enabled Size: 256 MB (Single-bank Connection)
Error Status: OK
Handle 0x0007, DMI type 6, 12 bytes
Memory Module Information
Socket Designation: A1
Bank Connections: 2 3
Current Speed: Unknown
Type: Other
Installed Size: 1024 MB (Double-bank Connection)
Enabled Size: 1024 MB (Double-bank Connection)
Error Status: OK
Handle 0x0008, DMI type 6, 12 bytes
Memory Module Information
Socket Designation: A2
Bank Connections: None
Current Speed: Unknown
Type: Unknown
Installed Size: Not Installed
Enabled Size: Not Installed
Error Status: OK
Handle 0x0009, DMI type 6, 12 bytes
Memory Module Information
Socket Designation: A3
Bank Connections: None
Current Speed: Unknown
Type: Unknown
Installed Size: Not Installed
Enabled Size: Not Installed
Error Status: OK
Handle 0x000A, DMI type 7, 19 bytes
Cache Information
Socket Designation: Internal Cache
Configuration: Enabled, Not Socketed, Level 1
Operational Mode: Write Back
Location: Internal
Installed Size: 32 KB
Maximum Size: 32 KB
Supported SRAM Types:
Synchronous
Installed SRAM Type: Synchronous
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x000B, DMI type 7, 19 bytes
Cache Information
Socket Designation: External Cache
Configuration: Enabled, Not Socketed, Level 2
Operational Mode: Write Back
Location: External
Installed Size: 1024 KB
Maximum Size: 1024 KB
Supported SRAM Types:
Synchronous
Installed SRAM Type: Synchronous
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x000C, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: PRIMARY IDE
Internal Connector Type: On Board IDE
External Reference Designator: Not Specified
External Connector Type: None
Port Type: Other
Handle 0x000D, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: SECONDARY IDE
Internal Connector Type: On Board IDE
External Reference Designator: Not Specified
External Connector Type: None
Port Type: Other
Handle 0x000E, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: FDD
Internal Connector Type: On Board Floppy
External Reference Designator: Not Specified
External Connector Type: None
Port Type: 8251 FIFO Compatible
Handle 0x000F, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: COM1
Internal Connector Type: 9 Pin Dual Inline (pin 10 cut)
External Reference Designator:
External Connector Type: DB-9 male
Port Type: Serial Port 16450 Compatible
Handle 0x0010, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: COM2
Internal Connector Type: 9 Pin Dual Inline (pin 10 cut)
External Reference Designator:
External Connector Type: DB-9 male
Port Type: Serial Port 16450 Compatible
Handle 0x0011, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: LPT1
Internal Connector Type: DB-25 female
External Reference Designator:
External Connector Type: DB-25 female
Port Type: Parallel Port ECP/EPP
Handle 0x0012, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: Keyboard
Internal Connector Type: PS/2
External Reference Designator:
External Connector Type: PS/2
Port Type: Keyboard Port
Handle 0x0013, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: PS/2 Mouse
Internal Connector Type: PS/2
External Reference Designator:
External Connector Type: PS/2
Port Type: Mouse Port
Handle 0x0014, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: Not Specified
Internal Connector Type: None
External Reference Designator: USB0
External Connector Type: Other
Port Type: USB
Handle 0x0015, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: Not Specified
Internal Connector Type: None
External Reference Designator: USB1
External Connector Type: Other
Port Type: USB
Handle 0x0016, DMI type 9, 13 bytes
System Slot Information
Designation: PCI0
Type: 32-bit PCI
Current Usage: Available
Length: Long
ID: 1
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x0017, DMI type 9, 13 bytes
System Slot Information
Designation: PCI1
Type: 32-bit PCI
Current Usage: Available
Length: Long
ID: 2
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x0018, DMI type 9, 13 bytes
System Slot Information
Designation: PCI2
Type: 32-bit PCI
Current Usage: Available
Length: Long
ID: 3
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x0019, DMI type 9, 13 bytes
System Slot Information
Designation: PCI3
Type: 32-bit PCI
Current Usage: Available
Length: Long
ID: 4
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x001A, DMI type 9, 13 bytes
System Slot Information
Designation: AGP
Type: 32-bit AGP
Current Usage: In Use
Length: Long
ID: 8
Characteristics:
5.0 V is provided
Handle 0x001B, DMI type 13, 22 bytes
BIOS Language Information
Installable Languages: 3
n|US|iso8859-1
n|US|iso8859-1
r|CA|iso8859-1
Currently Installed Language: n|US|iso8859-1
Handle 0x001C, DMI type 16, 15 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: None
Maximum Capacity: 4 GB
Error Information Handle: Not Provided
Number Of Devices: 4
Handle 0x001D, DMI type 17, 21 bytes
Memory Device
Array Handle: 0x001C
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 256 MB
Form Factor: DIMM
Set: None
Locator: A0
Bank Locator: Bank0/1
Type: SDRAM
Type Detail: Synchronous
Handle 0x001E, DMI type 17, 21 bytes
Memory Device
Array Handle: 0x001C
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: A1
Bank Locator: Bank2/3
Type: SDRAM
Type Detail: Synchronous
Handle 0x001F, DMI type 17, 21 bytes
Memory Device
Array Handle: 0x001C
Error Information Handle: Not Provided
Total Width: Unknown
Data Width: Unknown
Size: No Module Installed
Form Factor: DIMM
Set: None
Locator: A2
Bank Locator: Bank4/5
Type: Unknown
Type Detail: Unknown
Handle 0x0020, DMI type 17, 21 bytes
Memory Device
Array Handle: 0x001C
Error Information Handle: Not Provided
Total Width: Unknown
Data Width: Unknown
Size: No Module Installed
Form Factor: DIMM
Set: None
Locator: A3
Bank Locator: Bank6/7
Type: Unknown
Type Detail: Unknown
Handle 0x0021, DMI type 19, 15 bytes
Memory Array Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0004FFFFFFF
Range Size: 1280 MB
Physical Array Handle: 0x001C
Partition Width: 0
Handle 0x0022, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0000FFFFFFF
Range Size: 256 MB
Physical Device Handle: 0x001D
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Handle 0x0023, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00010000000
Ending Address: 0x0004FFFFFFF
Range Size: 1 GB
Physical Device Handle: 0x001E
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Handle 0x0024, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000000003FF
Range Size: 1 kB
Physical Device Handle: 0x001F
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Handle 0x0025, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000000003FF
Range Size: 1 kB
Physical Device Handle: 0x0020
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Handle 0x0026, DMI type 32, 11 bytes
System Boot Information
Status: No errors detected
Handle 0x0027, DMI type 127, 4 bytes
End Of Table
|
|
|
|
|
|
|
|
|
illukas
Vana Pingviin
Vanus: 44
Liitunud: 24.10.2006
Postitused: 2036
|
|
Epox EP-4PLAI
Kõik sõltub mis sul seal praegu peale ketta veel järgi on... Sellel emmel kaks sata pesa
Mitu seadet sul selle ata otsas on?
kuhu sa ruumi juurde tahad saada- kas linuxile või winile?
jne???
Sata on uuem ja kiirem standard, kuigi emme vist sata2-te ei toeta...
Mina ise ostaks sata ketta, linuxi poolelt vahet erilist ei ole peale selle et ketta tähis on hdx asemel sdx...
Pistad ketta sisse,
terminalis fdisk -l annab sulle teada milliseks linux selle pani kas sda sdb või sdd
teed partatsiooni
formaadid partatsiooni ext3 (ext4 veel ei soovita)
moundid külge vaatad kas töötab
kui töötas ühendad lahti, teed fdiski kirje ja mount -a
vuolaa ja peakski töötama
|
|
|
|
|
|
|
|
Huck
Pingviini aktivist
Vanus: 41
Liitunud: 20.10.2005
Postitused: 135
Asukoht: Tln-Kur
Distributsioon: Ubuntu 9.04
|
|
sata pesa on see "lapik" eks. Ühes on 2 dvd draivi ning teises HDD.
Uus ketas läheb ilmselt tervelt linux. (tüüpiline system+home+swap partiga)
Vana jätaks winni jaoks näiteks. (kindluse mõttes peaks vist ka failidele eraldi parti tegema)
|
|
|
|
|
|
|
|
sander85
Vana Pingviin
Vanus: 39
Liitunud: 08.08.2005
Postitused: 4359
Asukoht: Tallinn (vahel ka Virtsu)
Distributsioon: Mageia, Debian, CentOS
|
|
Huck kirjutas: | sata pesa on see "lapik" eks. Ühes on 2 dvd draivi ning teises HDD.
Uus ketas läheb ilmselt tervelt linux. (tüüpiline system+home+swap partiga)
Vana jätaks winni jaoks näiteks. (kindluse mõttes peaks vist ka failidele eraldi parti tegema) |
see lintkaabel on ikka tavaline ata
sata pesasi võid siit vaadata: http://en.wikipedia.org/wiki/Sata
ise soovitaks ka satat ikka
ja minuteada peaks uuemad kernelid ka ata kettad juba märkima kui /dev/sdX
kui tahad sinna kettale panna ainult linuxi, siis peaks vist piisama sellest kui bootimise järjekorras paned selle esimesekd seadmeks ja sealt juba peaks linuxi bootloader oskama hiljem tee ka windowsini juhatada, muud keerulist ei tohiks olla
|
|
|
|
_________________
|
|
|
|
Huck
Pingviini aktivist
Vanus: 41
Liitunud: 20.10.2005
Postitused: 135
Asukoht: Tln-Kur
Distributsioon: Ubuntu 9.04
|
|
Nagu pakutud siis emakaardil on tõesti 2 sata pesa. Nii et jääb siis sata kui nii soovitate.
Valida on veel kas 1.5 või 3 Gb/s ning nii 5400 kui 7200rpm. Kas kodukasutajale on neist kiirustest mingit erinevust? Või ikkagi mida kiirem seda parem?
HV lehel on esindatud samsung, western digital, seagate, hitachi... kas millestki peaks kindlasti kaarega mõõda käima?
sander85 kirjutas: | ...minuteada peaks uuemad kernelid ka ata kettad juba märkima kui /dev/sdX |
hda->sda muutus toimus vist üle aasta tagasi juba.
illukas kirjutas: | kuhu sa ruumi juurde tahad saada- kas linuxile või winile?
|
kuidas võtta... mõlemale? plaan on selline, et uuele kettale tervenisti värske ubuntu. andmed ümber tõsta uuele kettale, seejärel vanale kettale format ning tervelt puhas windooz selga.
|
|
|
|
|
|
|
|
sander85
Vana Pingviin
Vanus: 39
Liitunud: 08.08.2005
Postitused: 4359
Asukoht: Tallinn (vahel ka Virtsu)
Distributsioon: Mageia, Debian, CentOS
|
|
ma ei ole kindel, kas su emaplaat 3GB/s satat toetab üldse, pead seda emaplaadi dokumentatsioonist uurima, et millist satat see toetab veel
pöörete osas ikka 7200, vahe on märgatav selles osas..
ja tootjatest, omal on üks samsungi ketas läbi läinud küll, aga samas oli see laptopi oma ja vbl polnud ilus 2a jutti 24/7 sees hoida
kindlasti ei tohiks suuremaid probleeme tulla WD ja seagate'ga
|
|
|
|
_________________
|
|
|
|
johnsmith
Vana Pingviin
Vanus: 50
Liitunud: 24.07.2006
Postitused: 714
Asukoht: Universum
Distributsioon: Ubuntu/Gentoo/FreeBSD
|
|
Miks mitte siis juba 10000rpm ketas ei tea täpselt aga usun, et pöörlemiskiirus tavaliselt tähtsam kui andmete edastamis kiirus 1,5 vs 3 GB/s kuna arvatavasti pudelikaelaks on ikkagi andmete lugemise kiirus kettalt........
See hda -> sda tekitas mul igast jama gentoos fstabis ja hdparm ka ei töötanud enam ning pidin vastava sätte kernelist manuaalselt välja jätma. Ei tea millele see küll kasulik on.
|
|
|
|
_________________ "Thinking is the hardest work there is, which is probably the reason why so few engage in it" - Henry Ford
|
|
|
|
sander85
Vana Pingviin
Vanus: 39
Liitunud: 08.08.2005
Postitused: 4359
Asukoht: Tallinn (vahel ka Virtsu)
Distributsioon: Mageia, Debian, CentOS
|
|
|
|
Huck
Pingviini aktivist
Vanus: 41
Liitunud: 20.10.2005
Postitused: 135
Asukoht: Tln-Kur
Distributsioon: Ubuntu 9.04
|
|
SATA II ehk siis 3Gb/s kettad tunduvad üldiselt odavamad kui 1.5gb/s. Aga ma ei suuda seda välja peilida praegu kas Epox EP-4PLAI toetab 3gb/s.
Näiteks:
Seagate Momentus 7200.2 ST9160823AS 160GB 7200rpm 8MB SATA 1.5Gb/s 870kr.
Western Digital Caviar WD3200AAKS 320GB 7200rpm 16MB NCQ SATA 3Gb/s 625kr.
edit: kuigi interneti andmeil tundub, et sata II ketas toimib ka sata I mobo peal ainult et lihtsalt 1.5gb/s kiirusel...
Q: will an sata 2 drive work on an sata 1 board?
A: Yes, it will just operate in SATA I mode and with ncq disabled too.
|
|
|
|
|
|
|
|
xpander
Vana Pingviin
Vanus: 39
Liitunud: 27.06.2008
Postitused: 445
Asukoht: Localhost
Distributsioon: Arch Linux, MATE
|
|
SATA II kettalpeaks olema jumper et SATA I mode panna, vähemalt olen kohanud ühte sellist, kui ei eksi siis oli miski Seagate.
edit: http://www.tomshardware.co.uk/forum/page-184789_14_0.html
"Some HDDs have a jumper, others have a disk firmware modification utility to switch from SATA-I to SATA-II
Most SATA-II drives are sold with factory default settings set on SATA-I. So yes, it should work out of the box."
|
|
|
|
_________________ Mängude Videod Linuxi All: http://www.youtube.com/user/Xpander666
-----------
Gfire - Xfire For Pidgin
|
|
|
|
illukas
Vana Pingviin
Vanus: 44
Liitunud: 24.10.2006
Postitused: 2036
|
|
3gb kettad on ka tagurpidi ühilduvad!!!!
10 kettad on head ja kiirusevahe on üpris suur, nagu ka hinnavahe.
Enda viimastel ja töökoha arvutites kõigil 10k rpm kettad süsteemsete ketastena.
vihjena: sata2 ja 10k rpm raid5 massiiv millel 6 ketast- mmmmagus
Sata2 ketastel on reeglina buffer suurem, ketta mis iganes meetodid, materjalid, tarkvara on edasi arenenud, seega mina valiks igal juhul sata2 ketta ja vastavalt sellele kuidas rahakott lubab. Mingit ulme püssi sa sealt niikuinii ei saa...
|
|
|
|
|
|
|
|
Huck
Pingviini aktivist
Vanus: 41
Liitunud: 20.10.2005
Postitused: 135
Asukoht: Tln-Kur
Distributsioon: Ubuntu 9.04
|
|
Selge. Tänud kannatlikuse eest kõigile.
Hetkel jäi silma konkreetselt see:
Western Digital Caviar WD3200AAKS 320GB 7200rpm 16MB NCQ SATA 3Gb/s 650kr.
Arvutimaalimas ilusti kohal ka nii et võib ära tellida. Eks siis küsin edasi kui ketas käes:P
|
|
|
|
|
|
|
|
|
|