Portaal Portaal Pingviini veeb foorumi pealeht
  Viki  |  IRC  |  Otsing  |  Küsimused ja vastused  |  Profiil  |  Privaatsõnumite vaatamiseks logi sisse  | Logi sisse või Registreeru
<empty>
Vaata järgmist teemat
Vaata eelmist teemat

Postita uus teemaVasta teemale
Autor Sõnum
-IFFI-
Vana Pingviin
Vana Pingviin


Vanus: 43
Liitunud: 25.06.2005
Postitused: 1393
Asukoht: Lappeenranta-Turku
Distributsioon: Debian - MX Linux
finland.gif
postituspostitatud: 02.04.2015, 18:55  postituse pealkiri:  (teema puudub)  

Tänud kaar3l, sinu juhendiga sain vähemasti ruuteri webUI pildi taas ette ja üle traaditagi saab nuid ligi Smile

Tundub, et kusagil on miski viga ikkagi nüüd veel sees sest ei saa netti ma järgi vana 3G pulgaga mis varem töötas kenasti ja rääkimata 4G pulgast.

Vahetasin ka erinevaid tarkvara versioone ja proovisin ka oma vanu töötavaid backupe aga netti ei võta ruuter järgi.

Sinu antud õpetus terminalis on väljundina järgmine
Kood:
# sysupgrade openwrt.bin
Saving config files...
killall: watchdog: no process killed
Sending TERM to remaining processes ... ubusd askfirst logd netifd odhcpd ntpd dnsmasq
Sending KILL to remaining processes ... askfirst
Switching to ramdisk...
Performing system upgrade...
Unlocking firmware ...

Writing from <stdin> to firmware ...  [w]
   
Appending jffs2 data from /tmp/sysupgrade.tgz to firmware...
Writing from <stdin> to firmware ...  [w]TRX header not found
Error fixing up TRX header
   
Upgrade completed
Rebooting system...


Pärats rebooti oli siis webUI kenasti ees Smile

-E- Milleks see viimane link kasulik võib olla, oma oskamatu keelega ma sealt küll miskit vajaliku ei leidnud Embarassed Razz


Kaar3l
Vana Pingviin
Vana Pingviin


Vanus: 32
Liitunud: 07.05.2007
Postitused: 692
Asukoht: Plv
Distributsioon: Ubuntu
estonia.gif
postituspostitatud: 02.04.2015, 19:14  postituse pealkiri:  (teema puudub)  

Rõõm kuulda. Smile



Kas seda "MultiWeb 3.18 for 4 meg Routers" oled ka proovinud? Vaatasin, et on küll development versioon aga on uusim.

Seal selline jutt ka:
Tsitaat:
Hostless modems now appear on the Network Status page

Sul peaks see 4G pulk olema hostless.


http://ofmodemsandmen.com/downloadsm.html

_________________
Hyva päiva!

-IFFI-
Vana Pingviin
Vana Pingviin


Vanus: 43
Liitunud: 25.06.2005
Postitused: 1393
Asukoht: Lappeenranta-Turku
Distributsioon: Debian - MX Linux
finland.gif
postituspostitatud: 03.04.2015, 19:55  postituse pealkiri:  (teema puudub)  

Ei saa ma kuidagi sõbraks oma ruuterit ja 4G modemit Huawei E3276

Mingise nikerdamisega sain käima ja tööle oma 3G(teise netipulga) aga seda 4G oma ei taha kuidagi ühendada. Lambid ja kirjad kõik näitavad nagu peaks asi olema korras aga netipulgal vilgub ainult sinine tuluke mis näitab mitte neti olemas olu. Ruuteris modemi alt vaadates on modem kenasti kirjas...lisan juurde pildid
Image
Image

Pistan mõned logid mis ruuterist koppisin kui oli ühendatud 4G modem, ehk on neist miskit abi

===SYSTEM LOG===
Kood:
Tue Mar 10 19:29:49 2015 kern.info kernel: [   14.620000] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47
Tue Mar 10 19:29:49 2015 kern.info kernel: [   14.630000] cfg80211: Regulatory domain changed to country: US
Tue Mar 10 19:29:49 2015 kern.info kernel: [   14.630000] cfg80211:  DFS Master region: FCC
Tue Mar 10 19:29:49 2015 kern.info kernel: [   14.640000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Tue Mar 10 19:29:49 2015 kern.info kernel: [   14.650000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
Tue Mar 10 19:29:49 2015 kern.info kernel: [   14.660000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
Tue Mar 10 19:29:49 2015 kern.info kernel: [   14.660000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
Tue Mar 10 19:29:49 2015 kern.info kernel: [   14.670000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
Tue Mar 10 19:29:49 2015 kern.info kernel: [   14.680000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
Tue Mar 10 19:29:49 2015 kern.info kernel: [   16.270000] usb 1-1: USB disconnect, device number 2
Tue Mar 10 19:29:49 2015 kern.info kernel: [   16.690000] usb 1-1: new high-speed USB device number 3 using ehci-platform
Tue Mar 10 19:29:49 2015 kern.err kernel: [   17.310000] usb 1-1: device not accepting address 3, error -71
Tue Mar 10 19:29:49 2015 kern.info kernel: [   17.920000] usb 1-1: new high-speed USB device number 5 using ehci-platform
Tue Mar 10 19:29:53 2015 authpriv.info dropbear[816]: Not backgrounding
Tue Mar 10 19:29:55 2015 user.notice usb-modeswitch: Remove Early Modeswitch
Tue Mar 10 19:29:55 2015 user.emerg syslog: setting up led WAN
Tue Mar 10 19:29:55 2015 user.emerg syslog: setting up led LAN1
Tue Mar 10 19:29:55 2015 user.emerg syslog: setting up led LAN2
Tue Mar 10 19:29:55 2015 user.emerg syslog: setting up led LAN3
Tue Mar 10 19:29:55 2015 user.emerg syslog: setting up led LAN4
Tue Mar 10 19:29:55 2015 user.emerg syslog: setting up led WLAN
Tue Mar 10 19:29:55 2015 user.emerg syslog: setting up led USB
Tue Mar 10 19:29:56 2015 user.notice ROOter Initialize:  Initializing Rooter
Tue Mar 10 19:29:56 2015 user.emerg syslog: eth1      Link encap:Ethernet  HWaddr 10:FE:ED:E8:B6:78 
Tue Mar 10 19:29:56 2015 user.emerg syslog:           BROADCAST MULTICAST  MTU:1500  Metric:1
Tue Mar 10 19:29:56 2015 user.emerg syslog:           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
Tue Mar 10 19:29:56 2015 user.emerg syslog:           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
Tue Mar 10 19:29:56 2015 user.emerg syslog:           collisions:0 txqueuelen:1000
Tue Mar 10 19:29:56 2015 user.emerg syslog:           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
Tue Mar 10 19:29:56 2015 user.emerg syslog:           Interrupt:5
Tue Mar 10 19:29:56 2015 user.emerg syslog:
Tue Mar 10 19:29:56 2015 user.emerg syslog: uci: Entry not found
Tue Mar 10 19:29:57 2015 user.emerg syslog: Error: Failed to connect to ubus
Tue Mar 10 19:29:57 2015 user.emerg syslog: - init complete -
Tue Mar 10 19:29:58 2015 kern.info kernel: [   26.210000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Tue Mar 10 19:29:58 2015 kern.info kernel: [   26.210000] device eth1 entered promiscuous mode
Tue Mar 10 19:29:58 2015 kern.info kernel: [   26.220000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Tue Mar 10 19:29:58 2015 daemon.notice netifd: Interface 'lan' is enabled
Tue Mar 10 19:29:58 2015 daemon.notice netifd: Interface 'lan' is setting up now
Tue Mar 10 19:29:58 2015 daemon.notice netifd: Interface 'lan' is now up
Tue Mar 10 19:29:58 2015 kern.info kernel: [   26.230000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Tue Mar 10 19:29:58 2015 daemon.notice netifd: Interface 'wan6' is enabled
Tue Mar 10 19:29:58 2015 kern.info kernel: [   26.250000] device eth0 entered promiscuous mode
Tue Mar 10 19:29:58 2015 kern.info kernel: [   26.250000] br-wan: port 1(eth0) entered forwarding state
Tue Mar 10 19:29:58 2015 kern.info kernel: [   26.260000] br-wan: port 1(eth0) entered forwarding state
Tue Mar 10 19:29:58 2015 daemon.notice netifd: Interface 'wan' is enabled
Tue Mar 10 19:29:58 2015 daemon.notice netifd: Interface 'loopback' is enabled
Tue Mar 10 19:29:58 2015 daemon.notice netifd: Interface 'loopback' is setting up now
Tue Mar 10 19:29:58 2015 daemon.notice netifd: Interface 'loopback' is now up
Tue Mar 10 19:29:58 2015 daemon.notice netifd: Bridge 'br-wan' link is up
Tue Mar 10 19:29:58 2015 daemon.notice netifd: Interface 'wan' has link connectivity
Tue Mar 10 19:29:58 2015 daemon.notice netifd: Interface 'wan' is setting up now
Tue Mar 10 19:29:58 2015 daemon.notice netifd: Network device 'lo' link is up
Tue Mar 10 19:29:58 2015 daemon.notice netifd: Interface 'loopback' has link connectivity
Tue Mar 10 19:29:58 2015 daemon.notice netifd: wan (997): udhcpc (v1.22.1) started
Tue Mar 10 19:29:59 2015 daemon.notice netifd: wan (997): Sending discover...
Tue Mar 10 19:29:59 2015 daemon.notice netifd: wan (997): Performing a DHCP renew
Tue Mar 10 19:29:59 2015 daemon.notice netifd: wan (997): Sending discover...
Tue Mar 10 19:29:59 2015 kern.info kernel: [   27.140000] cfg80211: Calling CRDA for country: FI
Tue Mar 10 19:29:59 2015 kern.info kernel: [   27.150000] cfg80211: Regulatory domain changed to country: FI
Tue Mar 10 19:29:59 2015 kern.info kernel: [   27.160000] cfg80211:  DFS Master region: ETSI
Tue Mar 10 19:29:59 2015 kern.info kernel: [   27.170000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Tue Mar 10 19:29:59 2015 kern.info kernel: [   27.180000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Tue Mar 10 19:29:59 2015 kern.info kernel: [   27.180000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
Tue Mar 10 19:29:59 2015 kern.info kernel: [   27.190000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm), (0 s)
Tue Mar 10 19:29:59 2015 kern.info kernel: [   27.200000] cfg80211:   (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm), (0 s)
Tue Mar 10 19:29:59 2015 kern.info kernel: [   27.210000] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
Tue Mar 10 19:29:59 2015 daemon.notice netifd: Bridge 'br-wan' link is down
Tue Mar 10 19:29:59 2015 daemon.notice netifd: Interface 'wan' has link connectivity loss
Tue Mar 10 19:29:59 2015 kern.info kernel: [   27.230000] br-wan: port 1(eth0) entered disabled state
Tue Mar 10 19:30:00 2015 kern.info kernel: [   28.640000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Tue Mar 10 19:30:00 2015 kern.info kernel: [   28.660000] device wlan0 entered promiscuous mode
Tue Mar 10 19:30:01 2015 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Tue Mar 10 19:30:01 2015 kern.info kernel: [   29.330000] br-wan: port 2(wlan0) entered forwarding state
Tue Mar 10 19:30:01 2015 kern.info kernel: [   29.330000] br-wan: port 2(wlan0) entered forwarding state
Tue Mar 10 19:30:01 2015 kern.info kernel: [   29.340000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Tue Mar 10 19:30:01 2015 daemon.notice netifd: Bridge 'br-wan' link is up
Tue Mar 10 19:30:01 2015 daemon.notice netifd: Interface 'wan' has link connectivity
Tue Mar 10 19:30:01 2015 daemon.notice netifd: Network device 'wlan0' link is up
Tue Mar 10 19:30:01 2015 daemon.notice netifd: wan (997): Sending discover...
Tue Mar 10 19:30:01 2015 daemon.notice netifd: wan (997): Performing a DHCP renew
Tue Mar 10 19:30:03 2015 kern.info kernel: [   31.330000] br-wan: port 2(wlan0) entered forwarding state
Tue Mar 10 19:30:06 2015 daemon.info dnsmasq[1142]: started, version 2.72 cachesize 150
Tue Mar 10 19:30:06 2015 daemon.info dnsmasq[1142]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC loop-detect
Tue Mar 10 19:30:06 2015 daemon.info dnsmasq-dhcp[1142]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Tue Mar 10 19:30:06 2015 daemon.info dnsmasq[1142]: using local addresses only for domain lan
Tue Mar 10 19:30:06 2015 daemon.warn dnsmasq[1142]: no servers found in /tmp/resolv.conf.auto, will retry
Tue Mar 10 19:30:06 2015 daemon.info dnsmasq[1142]: read /etc/hosts - 1 addresses
Tue Mar 10 19:30:06 2015 daemon.info dnsmasq[1142]: read /tmp/hosts/dhcp - 1 addresses
Tue Mar 10 19:30:06 2015 daemon.info dnsmasq-dhcp[1142]: read /etc/ethers - 0 addresses
Tue Mar 10 19:30:08 2015 user.notice usb-modeswitch: Add : 1-1: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=? 12d1 14fe
Tue Mar 10 19:30:08 2015 user.notice usb-modeswitch: *****************************************************************
Tue Mar 10 19:30:08 2015 user.notice usb-modeswitch: *
Tue Mar 10 19:30:08 2015 user.notice usb-modeswitch: * Start of Modem Detection and Connection Information
Tue Mar 10 19:30:08 2015 user.notice usb-modeswitch: *
Tue Mar 10 19:30:08 2015 user.notice usb-modeswitch: * Product=HUAWEI_Mobile 12d1 14fe
Tue Mar 10 19:30:08 2015 user.notice usb-modeswitch: *
Tue Mar 10 19:30:08 2015 user.notice usb-modeswitch: *****************************************************************
Tue Mar 10 19:30:08 2015 kern.info kernel: [   36.840000] usb 1-1: USB disconnect, device number 5
Tue Mar 10 19:30:09 2015 kern.info kernel: [   37.280000] usb 1-1: new high-speed USB device number 6 using ehci-platform
Tue Mar 10 19:30:09 2015 kern.info kernel: [   37.440000] option 1-1:1.0: GSM modem (1-port) converter detected
Tue Mar 10 19:30:09 2015 kern.info kernel: [   37.460000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
Tue Mar 10 19:30:09 2015 kern.info kernel: [   37.470000] huawei_cdc_ncm 1-1:1.1: MAC-Address: 0c:5b:8f:27:9a:64
Tue Mar 10 19:30:09 2015 kern.info kernel: [   37.490000] huawei_cdc_ncm 1-1:1.1: cdc-wdm0: USB WDM device
Tue Mar 10 19:30:09 2015 kern.info kernel: [   37.490000] huawei_cdc_ncm 1-1:1.1 wwan0: register 'huawei_cdc_ncm' at usb-ehci-platform-1, Huawei CDC NCM device, 0c:5b:8f:27:9a:64
Tue Mar 10 19:30:12 2015 daemon.info hostapd: wlan0: STA 00:22:fa:c3:69:ee IEEE 802.11: authenticated
Tue Mar 10 19:30:12 2015 daemon.info hostapd: wlan0: STA 00:22:fa:c3:69:ee IEEE 802.11: associated (aid 1)
Tue Mar 10 19:30:13 2015 daemon.info hostapd: wlan0: STA 00:22:fa:c3:69:ee WPA: pairwise key handshake completed (RSN)
Tue Mar 10 19:30:18 2015 user.notice usb-modeswitch: *****************************************************************
Tue Mar 10 19:30:18 2015 user.notice usb-modeswitch: *
Tue Mar 10 19:30:18 2015 user.notice usb-modeswitch: * Switched to : 12d1:1506
Tue Mar 10 19:30:18 2015 user.notice usb-modeswitch: *
Tue Mar 10 19:30:18 2015 user.notice usb-modeswitch: *****************************************************************
Tue Mar 10 19:30:18 2015 user.notice Log Print : Driver Name : 1 option
Tue Mar 10 19:30:18 2015 user.notice Log Print : Driver Name : 2 huawei_cdc_ncm
Tue Mar 10 19:30:18 2015 user.notice Log Print : Driver Name : 3 huawei_cdc_ncm
Tue Mar 10 19:30:18 2015 user.notice usb-modeswitch: *****************************************************************
Tue Mar 10 19:30:18 2015 user.notice usb-modeswitch: *
Tue Mar 10 19:30:18 2015 user.notice usb-modeswitch: * ProtoFind returns : 4
Tue Mar 10 19:30:18 2015 user.notice usb-modeswitch: *
Tue Mar 10 19:30:18 2015 user.notice usb-modeswitch: *****************************************************************
Tue Mar 10 19:30:18 2015 user.notice usb-modeswitch: Found Modem1
Tue Mar 10 19:30:19 2015 user.notice usb-modeswitch: Connecting a Huawei NCM Modem
Tue Mar 10 19:30:19 2015 user.notice Create Connection: Start NCM Connection
Tue Mar 10 19:30:20 2015 user.notice usb-modeswitch: Ignoring Linux Hub
Tue Mar 10 19:30:24 2015 user.notice Create Connection: NCM Comm Port : /dev/ttyUSB0
Tue Mar 10 19:30:24 2015 user.notice Create Connection: Attempting to Connect
Tue Mar 10 19:30:31 2015 user.notice Create Connection: AT^NDISDUP=1,1,"","","",

OK

^RSSI:99
Tue Mar 10 19:30:31 2015 user.notice Create Connection: Connected
Tue Mar 10 19:30:39 2015 daemon.notice netifd: Interface 'wan1' is enabled
Tue Mar 10 19:30:39 2015 daemon.notice netifd: Network device 'wwan0' link is up
Tue Mar 10 19:30:39 2015 daemon.notice netifd: Interface 'wan1' has link connectivity
Tue Mar 10 19:30:39 2015 daemon.notice netifd: Interface 'wan1' is setting up now
Tue Mar 10 19:30:39 2015 user.notice sms start: SMS Supported
Tue Mar 10 19:30:39 2015 daemon.notice netifd: Interface 'wan1' is now down
Tue Mar 10 19:30:39 2015 daemon.notice netifd: Interface 'wan1' is disabled
Tue Mar 10 19:30:39 2015 daemon.notice netifd: Interface 'wan1' is enabled
Tue Mar 10 19:30:39 2015 daemon.notice netifd: Interface 'wan1' is setting up now
Tue Mar 10 19:30:39 2015 daemon.notice netifd: Network device 'wwan0' link is down
Tue Mar 10 19:30:39 2015 daemon.notice netifd: Interface 'wan1' has link connectivity loss
Tue Mar 10 19:30:39 2015 daemon.notice netifd: Network device 'wwan0' link is up
Tue Mar 10 19:30:39 2015 daemon.notice netifd: Interface 'wan1' has link connectivity
Tue Mar 10 19:30:40 2015 daemon.notice netifd: wan1 (1695): udhcpc (v1.22.1) started
Tue Mar 10 19:30:40 2015 daemon.notice netifd: wan1 (1695): Sending discover...
Tue Mar 10 19:30:40 2015 kern.info kernel: [   68.170000] device wlan0 left promiscuous mode
Tue Mar 10 19:30:40 2015 kern.info kernel: [   68.170000] br-wan: port 2(wlan0) entered disabled state
Tue Mar 10 19:30:40 2015 daemon.notice netifd: Bridge 'br-wan' link is down
Tue Mar 10 19:30:40 2015 daemon.notice netifd: Interface 'wan' has link connectivity loss
Tue Mar 10 19:30:40 2015 daemon.notice netifd: Network device 'wlan0' link is down
Tue Mar 10 19:30:40 2015 daemon.notice netifd: wan (997): Performing a DHCP renew
Tue Mar 10 19:30:40 2015 kern.info kernel: [   68.930000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Tue Mar 10 19:30:41 2015 kern.info kernel: [   69.510000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Tue Mar 10 19:30:41 2015 daemon.notice netifd: Network device 'wlan0' link is up
Tue Mar 10 19:30:41 2015 kern.info kernel: [   69.670000] device wlan0 entered promiscuous mode
Tue Mar 10 19:30:41 2015 kern.info kernel: [   69.680000] br-lan: port 2(wlan0) entered forwarding state
Tue Mar 10 19:30:41 2015 kern.info kernel: [   69.680000] br-lan: port 2(wlan0) entered forwarding state
Tue Mar 10 19:30:41 2015 kern.info kernel: [   69.700000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Tue Mar 10 19:30:41 2015 daemon.notice netifd: Bridge 'br-lan' link is up
Tue Mar 10 19:30:41 2015 daemon.notice netifd: Interface 'lan' has link connectivity
Tue Mar 10 19:30:43 2015 daemon.notice netifd: wan1 (1695): Sending discover...
Tue Mar 10 19:30:43 2015 kern.info kernel: [   71.680000] br-lan: port 2(wlan0) entered forwarding state
Tue Mar 10 19:30:46 2015 daemon.notice netifd: wan1 (1695): Sending discover...
Tue Mar 10 19:30:51 2015 daemon.info hostapd: wlan0: STA 00:22:fa:c3:69:ee IEEE 802.11: authenticated
Tue Mar 10 19:30:51 2015 daemon.info hostapd: wlan0: STA 00:22:fa:c3:69:ee IEEE 802.11: associated (aid 1)
Tue Mar 10 19:30:52 2015 daemon.info hostapd: wlan0: STA 00:22:fa:c3:69:ee WPA: pairwise key handshake completed (RSN)
Tue Mar 10 19:30:54 2015 daemon.info dnsmasq-dhcp[1142]: DHCPDISCOVER(br-lan) 192.168.1.200 00:22:fa:c3:69:ee
Tue Mar 10 19:30:54 2015 daemon.info dnsmasq-dhcp[1142]: DHCPOFFER(br-lan) 192.168.1.200 00:22:fa:c3:69:ee
Tue Mar 10 19:30:54 2015 daemon.info dnsmasq-dhcp[1142]: DHCPREQUEST(br-lan) 192.168.1.200 00:22:fa:c3:69:ee
Tue Mar 10 19:30:54 2015 daemon.info dnsmasq-dhcp[1142]: DHCPACK(br-lan) 192.168.1.200 00:22:fa:c3:69:ee iffi
Tue Mar 10 19:31:28 2015 kern.info kernel: [  116.340000] usb 1-1: USB disconnect, device number 6
Tue Mar 10 19:31:28 2015 kern.err kernel: [  116.340000] option1 ttyUSB0: usb_wwan_indat_callback: resubmit read urb failed. (-19)
Tue Mar 10 19:31:28 2015 kern.err kernel: [  116.340000] option1 ttyUSB0: usb_wwan_indat_callback: resubmit read urb failed. (-19)
Tue Mar 10 19:31:28 2015 kern.err kernel: [  116.340000] option1 ttyUSB0: usb_wwan_indat_callback: resubmit read urb failed. (-19)
Tue Mar 10 19:31:28 2015 kern.err kernel: [  116.340000] option1 ttyUSB0: usb_wwan_indat_callback: resubmit read urb failed. (-19)
Tue Mar 10 19:31:28 2015 kern.info kernel: [  116.460000] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
Tue Mar 10 19:31:28 2015 kern.info kernel: [  116.470000] option 1-1:1.0: device disconnected
Tue Mar 10 19:31:28 2015 kern.info kernel: [  116.470000] huawei_cdc_ncm 1-1:1.1 wwan0: unregister 'huawei_cdc_ncm' usb-ehci-platform-1, Huawei CDC NCM device
Tue Mar 10 19:31:28 2015 daemon.notice netifd: Network device 'wwan0' link is down
Tue Mar 10 19:31:28 2015 daemon.notice netifd: Interface 'wan1' has link connectivity loss
Tue Mar 10 19:31:28 2015 daemon.notice netifd: wan1 (1695): Read error: Network is down, reopening socket
Tue Mar 10 19:31:28 2015 daemon.notice netifd: wan1 (1695): udhcpc: bind: No such device
Tue Mar 10 19:31:28 2015 daemon.notice netifd: Interface 'wan1' is now down
Tue Mar 10 19:31:28 2015 daemon.notice netifd: Interface 'wan1' is disabled
Tue Mar 10 19:31:28 2015 kern.info kernel: [  116.790000] usb 1-1: new high-speed USB device number 7 using ehci-platform
Tue Mar 10 19:31:29 2015 kern.info kernel: [  116.970000] option 1-1:1.0: GSM modem (1-port) converter detected
Tue Mar 10 19:31:29 2015 kern.info kernel: [  116.970000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
Tue Mar 10 19:31:29 2015 kern.info kernel: [  116.990000] huawei_cdc_ncm 1-1:1.1: MAC-Address: 0c:5b:8f:27:9a:64
Tue Mar 10 19:31:29 2015 kern.info kernel: [  117.010000] huawei_cdc_ncm 1-1:1.1: cdc-wdm0: USB WDM device
Tue Mar 10 19:31:29 2015 kern.info kernel: [  117.060000] huawei_cdc_ncm 1-1:1.1 wwan0: register 'huawei_cdc_ncm' at usb-ehci-platform-1, Huawei CDC NCM device, 0c:5b:8f:27:9a:64
Tue Mar 10 19:31:29 2015 daemon.notice netifd: Interface 'wan1' is enabled
Tue Mar 10 19:31:29 2015 daemon.notice netifd: Network device 'wwan0' link is up
Tue Mar 10 19:31:29 2015 daemon.notice netifd: Interface 'wan1' has link connectivity
Tue Mar 10 19:31:29 2015 daemon.notice netifd: Interface 'wan1' is setting up now
Tue Mar 10 19:31:29 2015 daemon.notice netifd: wan1 (2233): udhcpc (v1.22.1) started
Tue Mar 10 19:31:29 2015 daemon.notice netifd: wan1 (2233): Sending discover...
Tue Mar 10 19:31:32 2015 daemon.notice netifd: wan1 (2233): Sending discover...
Tue Mar 10 19:31:35 2015 daemon.notice netifd: wan1 (2233): Sending discover...
Tue Mar 10 19:37:13 2015 user.notice Connection Monitor: Modem 1 Connection is Down


===KERNEL LOG===
Kood:
[    0.000000] Linux version 3.10.58 (user@mint12) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43228) ) #10 Tue Mar 10 09:22:31 PDT 2015
[    0.000000] MyLoader: sysp=e72c40a6, boardp=3050a00a, parts=15d661ab
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9341 rev 3
[    0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 803329b0, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8192 pages, LIFO batch:0
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-MR3420-v2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 28592k/32768k available (2348k kernel code, 4176k reserved, 632k data, 280k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.070000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] MIPS: machine is TP-LINK TL-MR3420 v2
[    0.510000] bio: create slab <bio-0> at 0
[    0.520000] usbcore: registered new interface driver usbfs
[    0.520000] usbcore: registered new interface driver hub
[    0.530000] usbcore: registered new device driver usb
[    0.530000] Switching to clocksource MIPS
[    0.540000] NET: Registered protocol family 2
[    0.540000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.550000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.560000] TCP: Hash tables configured (established 512 bind 512)
[    0.560000] TCP: reno registered
[    0.570000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.570000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.580000] NET: Registered protocol family 1
[    0.580000] PCI: CLS 0 bytes, default 32
[    0.600000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.600000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.610000] msgmni has been set to 55
[    0.620000] io scheduler noop registered
[    0.620000] io scheduler deadline registered (default)
[    0.630000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.650000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.660000] console [ttyS0] enabled, bootconsole disabled
[    0.670000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[    0.680000] m25p80 spi0.0: found s25sl032p, expected m25p80
[    0.690000] m25p80 spi0.0: s25sl032p (4096 Kbytes)
[    0.690000] 5 tp-link partitions found on MTD device spi0.0
[    0.700000] Creating 5 MTD partitions on "spi0.0":
[    0.710000] 0x000000000000-0x000000020000 : "u-boot"
[    0.710000] 0x000000020000-0x00000012ea54 : "kernel"
[    0.720000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.730000] 0x00000012ea54-0x0000003f0000 : "rootfs"
[    0.740000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.750000] mtd: device 2 (rootfs) set to be root filesystem
[    0.760000] 1 squashfs-split partitions found on MTD device rootfs
[    0.760000] 0x000000390000-0x0000003f0000 : "rootfs_data"
[    0.770000] 0x0000003f0000-0x000000400000 : "art"
[    0.780000] 0x000000020000-0x0000003f0000 : "firmware"
[    0.800000] libphy: ag71xx_mdio: probed
[    1.360000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
[    1.370000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    1.920000] ag71xx-mdio.1: Found an AR934X built-in switch
[    2.960000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    2.960000] usbcore: registered new interface driver cdc_ncm
[    2.970000] usbcore: registered new interface driver huawei_cdc_ncm
[    2.980000] usbcore: registered new interface driver cdc_wdm
[    2.990000] TCP: cubic registered
[    2.990000] NET: Registered protocol family 17
[    3.000000] 8021q: 802.1Q VLAN Support v1.8
[    3.010000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    3.020000] Freeing unused kernel memory: 280K (8034a000 - 80390000)
[    5.460000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.470000] ehci-platform: EHCI generic platform driver
[    5.470000] ehci-platform ehci-platform: EHCI Host Controller
[    5.480000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    5.490000] ehci-platform ehci-platform: TX-TX IDP fix enabled
[    5.490000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    5.520000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    5.520000] hub 1-0:1.0: USB hub found
[    5.530000] hub 1-0:1.0: 1 port detected
[    5.530000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    5.540000] uhci_hcd: USB Universal Host Controller Interface driver
[    9.630000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[   11.190000] jffs2: notice: (335) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 24 of xref (0 dead, 9 orphan) found.
[   14.130000] NET: Registered protocol family 10
[   14.140000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   14.160000] usbcore: registered new interface driver cdc_ether
[   14.170000] usbcore: registered new interface driver cdc_mbim
[   14.180000] Loading modules backported from Linux version master-2014-11-04-0-gf3660a2
[   14.190000] Backport generated by backports.git backports-20141023-2-g4ff890b
[   14.200000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.210000] nf_conntrack version 0.5.0 (451 buckets, 1804 max)
[   14.240000] usbcore: registered new interface driver qmi_wwan
[   14.250000] usbcore: registered new interface driver rndis_host
[   14.260000] usbcore: registered new interface driver sierra_net
[   14.270000] usbcore: registered new interface driver usbserial
[   14.270000] usbcore: registered new interface driver usbserial_generic
[   14.280000] usbserial: USB Serial support registered for generic
[   14.330000] xt_time: kernel timezone is -0000
[   14.350000] cfg80211: Calling CRDA to update world regulatory domain
[   14.360000] cfg80211: World regulatory domain updated:
[   14.370000] cfg80211:  DFS Master region: unset
[   14.370000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   14.380000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   14.390000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   14.400000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   14.410000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[   14.420000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   14.430000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   14.430000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   14.440000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   14.490000] PPP generic driver version 2.4.2
[   14.500000] NET: Registered protocol family 24
[   14.510000] usbcore: registered new interface driver sierra
[   14.510000] usbserial: USB Serial support registered for Sierra USB modem
[   14.560000] usbcore: registered new interface driver option
[   14.560000] usbserial: USB Serial support registered for GSM modem (1-port)
[   14.590000] ath: EEPROM regdomain: 0x0
[   14.590000] ath: EEPROM indicates default country code should be used
[   14.590000] ath: doing EEPROM country->regdmn map search
[   14.590000] ath: country maps to regdmn code: 0x3a
[   14.590000] ath: Country alpha2 being used: US
[   14.590000] ath: Regpair used: 0x3a
[   14.610000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   14.610000] cfg80211: Calling CRDA for country: US
[   14.620000] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47
[   14.630000] cfg80211: Regulatory domain changed to country: US
[   14.630000] cfg80211:  DFS Master region: FCC
[   14.640000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   14.650000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[   14.660000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[   14.660000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[   14.670000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[   14.680000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[   16.270000] usb 1-1: USB disconnect, device number 2
[   16.690000] usb 1-1: new high-speed USB device number 3 using ehci-platform
[   17.310000] usb 1-1: device not accepting address 3, error -71
[   17.920000] usb 1-1: new high-speed USB device number 5 using ehci-platform
[   26.210000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   26.210000] device eth1 entered promiscuous mode
[   26.220000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   26.230000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   26.250000] device eth0 entered promiscuous mode
[   26.250000] br-wan: port 1(eth0) entered forwarding state
[   26.260000] br-wan: port 1(eth0) entered forwarding state
[   27.140000] cfg80211: Calling CRDA for country: FI
[   27.150000] cfg80211: Regulatory domain changed to country: FI
[   27.160000] cfg80211:  DFS Master region: ETSI
[   27.170000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   27.180000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   27.180000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   27.190000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm), (0 s)
[   27.200000] cfg80211:   (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm), (0 s)
[   27.210000] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[   27.230000] br-wan: port 1(eth0) entered disabled state
[   28.640000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   28.660000] device wlan0 entered promiscuous mode
[   29.330000] br-wan: port 2(wlan0) entered forwarding state
[   29.330000] br-wan: port 2(wlan0) entered forwarding state
[   29.340000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   31.330000] br-wan: port 2(wlan0) entered forwarding state
[   36.840000] usb 1-1: USB disconnect, device number 5
[   37.280000] usb 1-1: new high-speed USB device number 6 using ehci-platform
[   37.440000] option 1-1:1.0: GSM modem (1-port) converter detected
[   37.460000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[   37.470000] huawei_cdc_ncm 1-1:1.1: MAC-Address: 0c:5b:8f:27:9a:64
[   37.490000] huawei_cdc_ncm 1-1:1.1: cdc-wdm0: USB WDM device
[   37.490000] huawei_cdc_ncm 1-1:1.1 wwan0: register 'huawei_cdc_ncm' at usb-ehci-platform-1, Huawei CDC NCM device, 0c:5b:8f:27:9a:64
[   68.170000] device wlan0 left promiscuous mode
[   68.170000] br-wan: port 2(wlan0) entered disabled state
[   68.930000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   69.510000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   69.670000] device wlan0 entered promiscuous mode
[   69.680000] br-lan: port 2(wlan0) entered forwarding state
[   69.680000] br-lan: port 2(wlan0) entered forwarding state
[   69.700000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   71.680000] br-lan: port 2(wlan0) entered forwarding state
[  116.340000] usb 1-1: USB disconnect, device number 6
[  116.340000] option1 ttyUSB0: usb_wwan_indat_callback: resubmit read urb failed. (-19)
[  116.340000] option1 ttyUSB0: usb_wwan_indat_callback: resubmit read urb failed. (-19)
[  116.340000] option1 ttyUSB0: usb_wwan_indat_callback: resubmit read urb failed. (-19)
[  116.340000] option1 ttyUSB0: usb_wwan_indat_callback: resubmit read urb failed. (-19)
[  116.460000] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[  116.470000] option 1-1:1.0: device disconnected
[  116.470000] huawei_cdc_ncm 1-1:1.1 wwan0: unregister 'huawei_cdc_ncm' usb-ehci-platform-1, Huawei CDC NCM device
[  116.790000] usb 1-1: new high-speed USB device number 7 using ehci-platform
[  116.970000] option 1-1:1.0: GSM modem (1-port) converter detected
[  116.970000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[  116.990000] huawei_cdc_ncm 1-1:1.1: MAC-Address: 0c:5b:8f:27:9a:64
[  117.010000] huawei_cdc_ncm 1-1:1.1: cdc-wdm0: USB WDM device
[  117.060000] huawei_cdc_ncm 1-1:1.1 wwan0: register 'huawei_cdc_ncm' at usb-ehci-platform-1, Huawei CDC NCM device, 0c:5b:8f:27:9a:64


Modem Debug Information

Kood:
OK
AT+CGEQNEG=1
OK
 
Tue Mar 10 19:30:44 2015 : /dev/ttyUSB0 AT+CREG=2
OK
AT+CREG?
+CREG: 2,2
OK
AT+CGREG=2
OK
AT+CGREG?
+CGREG: 2,2
OK
AT+CGEQNEG=1
OK
 
Tue Mar 10 19:30:46 2015 : /dev/ttyUSB0 AT+CPMS="SM"
+CPMS: 0,20,0,20,0,20
OK
 
Tue Mar 10 19:31:28 2015 : /dev/ttyUSB0 AT+CSQ
+CSQ: 99,99
OK
AT^CSNR?
^CSNR: -145,-32
OK
AT^SYSINFOEX
^SYSINFOEX:1,3,0,1,,6,"LTE",101,"LTE"
OK
AT^SYSCFGEX?
^SYSCFGEX:"00",3FFFFFFF,1,2,800C5
OK
AT^SYSCFG?
^SYSCFG:2,0,3FFFFFFF,1,2
OK
AT^SYSINFO
^SYSINFO:1,3,0,5,1,,4
OK
AT^LTERSRP?
COMMAND NOT SUPPORT
^RSSI:99
^RSSI:99
^RSSI:99
^RSSI:99
^MODE: 5,4
 
Tue Mar 10 19:31:30 2015 : /dev/ttyUSB0 AT+CPMS="SM"
+CPMS: 0,20,0,20,0,20
OK


DEVICE INFORMATION

Device Information
      
   T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1    
   B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0    
   D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1    
   P: Vendor=1d6b ProdID=0002 Rev= 3.10    
   S: Manufacturer=Linux 3.10.58 ehci_hcd    
   S: Product=EHCI Host Controller    
   S: SerialNumber=ehci-platform    
   C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA    
   I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub    
   E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms    
   ********************************************************************************************************    
   T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0    
   D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1    
   P: Vendor=12d1 ProdID=1506 Rev= 1.02    
   S: Manufacturer=HUAWEI Technology    
   S: Product=HUAWEI Mobile    
   C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=500mA    
   I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=12 Driver=option    
   E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms    
   E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms    
   I: If#= 1 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=02 Prot=16 Driver=huawei_cdc_ncm    
   E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=2ms    
   I:* If#= 1 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=16 Driver=huawei_cdc_ncm    
   E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=2ms    
   E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms    
   E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms    
   I:* If#= 2 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)    
   E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms    
   E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms    
   I:* If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)    
   E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms    
   E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms


Eile õhtal tegin igasugu katseid, lasin uusi ja erinevaid tarkvarasid openWRT omasi peale, tõstsin SIM kaarti ühest modemist teise ja vahetasin neid. Siis mingil hetkel korra proovides wifi-t korra jõudis pool netilehte ette laadida ja siis kadus ühendus ja siiani pole saanud...enam ei mäleta ka milline soft oli kasutusel. Aga on kindel, et modem töötas vähemasti selle ruuteriga.

On veel mingeid võimalus see 4G netipulk ruuteriga sõbraks teha? Is eolen ka kuhjaga googeldanud kuid midagi asjaliku nagu pole leidnud Sad


Kaar3l
Vana Pingviin
Vana Pingviin


Vanus: 32
Liitunud: 07.05.2007
Postitused: 692
Asukoht: Plv
Distributsioon: Ubuntu
estonia.gif
postituspostitatud: 03.04.2015, 20:02  postituse pealkiri:  (teema puudub)  

The way to avoid this is to change the IP address of the router. In the router web interface go to Network -> Interfaces and click on the Edit button for the LAN. Change the IPv4 address to 192.168.100.1 and then click on Save & Apply. You will have to manually change the IP address to 192.168.100.1 in the web browser in order to get back to the router's web interface.


Seda ka proovisid?

_________________
Hyva päiva!

-IFFI-
Vana Pingviin
Vana Pingviin


Vanus: 43
Liitunud: 25.06.2005
Postitused: 1393
Asukoht: Lappeenranta-Turku
Distributsioon: Debian - MX Linux
finland.gif
postituspostitatud: 03.04.2015, 20:40  postituse pealkiri:  (teema puudub)  

Sai siis nuid see ka proovitud nii nagu kästud juhendis. Tegin ka restardi modemile ja mitu korda võtsin ka ära netipulga järelt aga ei ühendu netti netipulk.
WebUI-s näitab kenasti infot pulga kohta...

IP-d on ka nagu teised nuid kui muutsin ära

oma masinas näitab hetkel
Kood:
$ ifconfig
eth0      Link encap:Ethernet  HWaddr 00:22:68:0c:79:0e 
          UP BROADCAST MULTICAST  MTU:1500 meetrika:1
          RX pakette:14931 vigu:0 ära visatud:0 ületäit:0 kaadri vigu:0
          TX pakette:16973 vigu:0 ära visatud:0 ületäit:0 carrier:0
          kollisioone:0 txqueuelen:1000
          RX baite:2771391 (2.7 MB)  TX baite:1802842 (1.8 MB)
          katkestus:20 mälu:fc000000-fc020000

lo        Link encap:Kohalik loopback 
          inet aadress:127.0.0.1  mask:255.0.0.0
          inet6 aadr: ::1/128 skoop:host
          UP LOOPBACK RUNNING  MTU:65536 meetrika:1
          RX pakette:46364 vigu:0 ära visatud:0 ületäit:0 kaadri vigu:0
          TX pakette:46364 vigu:0 ära visatud:0 ületäit:0 carrier:0
          kollisioone:0 txqueuelen:0
          RX baite:3655581 (3.6 MB)  TX baite:3655581 (3.6 MB)

wlan0     Link encap:Ethernet  HWaddr 00:22:fa:c3:69:ee 
          inet aadress:192.168.100.200  bcast:192.168.100.255  mask:255.255.255.0
          inet6 aadr: fe80::222:faff:fec3:69ee/64 skoop:ühendus
          inet6 aadr: fd6e:1533:22dc:0:222:faff:fec3:69ee/64 skoop:globaalne
          inet6 aadr: fd6e:1533:22dc:0:5d6a:8f6e:fa8d:a4df/64 skoop:globaalne
          UP BROADCAST RUNNING MULTICAST  MTU:1500 meetrika:1
          RX pakette:106313 vigu:0 ära visatud:0 ületäit:0 kaadri vigu:0
          TX pakette:99072 vigu:0 ära visatud:0 ületäit:0 carrier:0
          kollisioone:0 txqueuelen:1000
          RX baite:85255974 (85.2 MB)  TX baite:18389195 (18.3 MB)


ja webUI-s selline pilt
Image


Kaar3l
Vana Pingviin
Vana Pingviin


Vanus: 32
Liitunud: 07.05.2007
Postitused: 692
Asukoht: Plv
Distributsioon: Ubuntu
estonia.gif
postituspostitatud: 03.04.2015, 21:29  postituse pealkiri:  (teema puudub)  

Tundub ok see pool.

Huvitav oleks, kui logiks ruuterisse sisse terminalis. Siis tahaks mõne faili sisu näha. Näiteks võiks:

cat /etc/config/network

Kui seal pole korralikke pulga settinguid, siis ei saagi töötada. Smile

_________________
Hyva päiva!

-IFFI-
Vana Pingviin
Vana Pingviin


Vanus: 43
Liitunud: 25.06.2005
Postitused: 1393
Asukoht: Lappeenranta-Turku
Distributsioon: Debian - MX Linux
finland.gif
postituspostitatud: 04.04.2015, 05:02  postituse pealkiri:  (teema puudub)  

Tundub vist jah, et pole õiged seaded. Eriti ma küll aru ei saa aga nägin kirja 3G ja sellepärast arvangi Smile

Aga terminali väljund
Kood:
root@ROOter:~# cat /etc/config/network

config interface 'loopback'
   option ifname 'lo'
   option proto 'static'
   option ipaddr '127.0.0.1'
   option netmask '255.0.0.0'

config globals 'globals'
   option ula_prefix 'fd6e:1533:22dc::/48'

config interface 'lan'
   option ifname 'eth1'
   option force_link '1'
   option type 'bridge'
   option proto 'static'
   option netmask '255.255.255.0'
   option ip6assign '60'
   option ipaddr '192.168.100.1'

config interface 'wan'
   option _orig_ifname 'eth0'
   option _orig_bridge 'true'
   option proto '3g'
   option device '/dev/ttyS0'
   option service 'evdo'

config interface 'wan6'
   option ifname 'eth0'
   option proto 'dhcpv6'
   option type 'bridge'

config switch
   option name 'switch0'
   option reset '1'
   option enable_vlan '1'

config switch_vlan
   option device 'switch0'
   option vlan '1'
   option ports '0 1 2 3 4'

config interface 'wan1'
   option _orig_ifname 'eth1'
   option _orig_bridge 'false'
   option proto '3g'
   option service 'umts'
   option keepalive '10'
   option device '/dev/ttyUSB0'
   option metric '10'
   option pppd_options 'debug noipdefault'


Kaar3l
Vana Pingviin
Vana Pingviin


Vanus: 32
Liitunud: 07.05.2007
Postitused: 692
Asukoht: Plv
Distributsioon: Ubuntu
estonia.gif
postituspostitatud: 04.04.2015, 08:13  postituse pealkiri:  (teema puudub)  

Muuda see esimeses wan osas asju selliseks:
Kood:
.....

config interface 'wan'
   option _orig_ifname 'eth0'
   option _orig_bridge 'true'
   option proto 'ncm'
   option apn 'internet'
   option device '/dev/ttyUSB0'

.....

_________________
Hyva päiva!

-IFFI-
Vana Pingviin
Vana Pingviin


Vanus: 43
Liitunud: 25.06.2005
Postitused: 1393
Asukoht: Lappeenranta-Turku
Distributsioon: Debian - MX Linux
finland.gif
postituspostitatud: 04.04.2015, 16:32  postituse pealkiri:  (teema puudub)  

Sad Sad kahjuks ei andnud see mingit tulemust, Kül ma proovisin võta pärast muutusi paar kolm korda tagant ära netipulka ja siis restartisin ruuterit kuid ikka vilgub tuluke netipulgas ja ei mingit ühendust.

Ahjaa, WebUi lehel ei näita ka enam mingit infot nagu üleval pool olevatel piltidel

Conf fail hetkel selline
Kood:
root@ROOter:~#  cat /etc/config/network

config interface 'loopback'
   option ifname 'lo'
   option proto 'static'
   option ipaddr '127.0.0.1'
   option netmask '255.0.0.0'

config globals 'globals'
   option ula_prefix 'fd6e:1533:22dc::/48'

config interface 'lan'
   option ifname 'eth1'
   option force_link '1'
   option type 'bridge'
   option proto 'static'
   option netmask '255.255.255.0'
   option ip6assign '60'
   option ipaddr '192.168.100.1'

config interface 'wan'
   option _orig_ifname 'eth0'
   option _orig_bridge 'true'
   option proto 'ncm'
   option apn 'internet'
   option device '/dev/ttyUSB0'

config interface 'wan6'
   option ifname 'eth0'
   option proto 'dhcpv6'
   option type 'bridge'

config switch
   option name 'switch0'
   option reset '1'
   option enable_vlan '1'

config switch_vlan
   option device 'switch0'
   option vlan '1'
   option ports '0 1 2 3 4'


Kaar3l
Vana Pingviin
Vana Pingviin


Vanus: 32
Liitunud: 07.05.2007
Postitused: 692
Asukoht: Plv
Distributsioon: Ubuntu
estonia.gif
postituspostitatud: 06.04.2015, 14:04  postituse pealkiri:  (teema puudub)  

https://sites.google.com/site/variousopenwrt/huawei-e3267

Tsitaat:

If you have upgraded your firmware to the PPP version, all this does does not work at all.

You can find firmware upgrades from this page: http://3ginfo.ru/download59.html and

NCM is used with revisions 21.192.*.*(.*)

_________________
Hyva päiva!

Näita (aja järgi):      
Postita uus teemaVasta teemale


Vaata järgmist teemat
Vaata eelmist teemat
Powered by phpBB2 Plus based on phpBB © 2001/7 phpBB Group