Portaal Portaal Pingviini veeb foorumi pealeht
  Viki  |  IRC  |  Otsing  |  Küsimused ja vastused  |  Profiil  |  Privaatsõnumite vaatamiseks logi sisse  | Logi sisse või Registreeru
<empty>
Vaata järgmist teemat
Vaata eelmist teemat

Postita uus teemaVasta teemale
Autor Sõnum
maq
Pingviini aktivist
Pingviini aktivist



Liitunud: 16.08.2005
Postitused: 162

Distributsioon: Kubuntu 13.10
estonia.gif
postituspostitatud: 10.10.2007, 22:18  postituse pealkiri:  Kubuntu on tülis mälupulgaga  

Mure siis elline, et mälupulk tuntakse küll ära aga ühendus pulgaga kaob mingi 30sekundi pärast. Millest see küll tingitud olla võib?


spott
Admin
Admin


Vanus: 43
Liitunud: 04.06.2005
Postitused: 8853

Distributsioon: Ubuntu
estonia.gif
postituspostitatud: 11.10.2007, 06:12  postituse pealkiri:  (teema puudub)  

ühenda mälupulk arvutiga ja peale seda, kui ühendus katkenud, anna dmesg väljund siia

_________________
Tellige endale sünnipäevaks, sõbrapäevaks või muuks tähtpäevaks kingitus: Kingitused internetist - NetiKink.eu

maq
Pingviini aktivist
Pingviini aktivist



Liitunud: 16.08.2005
Postitused: 162

Distributsioon: Kubuntu 13.10
estonia.gif
postituspostitatud: 11.10.2007, 21:19  postituse pealkiri:  (teema puudub)  

[ 0.000000] Linux version 2.6.20-16-generic (root@terranova) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Sun Sep 23 19:50:39 UTC 2007 (Ubuntu 2.6.20-16.32-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000000fef0000 end: 000000000fff0000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000fff0000 size: 0000000000008000 end: 000000000fff8000 type: 3
[ 0.000000] copy_e820_map() start: 000000000fff8000 size: 0000000000008000 end: 0000000010000000 type: 4
[ 0.000000] copy_e820_map() start: 00000000fec00000 size: 0000000000100000 end: 00000000fed00000 type: 2
[ 0.000000] copy_e820_map() start: 00000000fee00000 size: 0000000000100000 end: 00000000fef00000 type: 2
[ 0.000000] copy_e820_map() start: 00000000ffee0000 size: 000000000002ffff end: 00000000fff0ffff type: 2
[ 0.000000] copy_e820_map() start: 00000000fffc0000 size: 0000000000040000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
[ 0.000000] BIOS-e820: 000000000fff0000 - 000000000fff8000 (ACPI data)
[ 0.000000] BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fed00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffee0000 - 00000000fff0ffff (reserved)
[ 0.000000] BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 255MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000fb960
[ 0.000000] Entering add_active_range(0, 0, 65520) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 65520
[ 0.000000] HighMem 65520 -> 65520
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 65520
[ 0.000000] On node 0 totalpages: 65520
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 479 pages used for memmap
[ 0.000000] Normal zone: 60945 pages, LIFO batch:15
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP (v000 AMI ) @ 0x000fa150
[ 0.000000] ACPI: RSDT (v001 AMIINT SiS645XX 0x00000010 MSFT 0x0100000b) @ 0x0fff0000
[ 0.000000] ACPI: FADT (v001 AMIINT SiS645XX 0x00000011 MSFT 0x0100000b) @ 0x0fff0030
[ 0.000000] ACPI: MADT (v001 AMIINT SiS645XX 0x00001000 MSFT 0x0100000b) @ 0x0fff00c0
[ 0.000000] ACPI: DSDT (v001 SiS 645 0x00001000 MSFT 0x0100000d) @ 0x00000000
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:2 APIC version 20
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 10000000:eec00000)
[ 0.000000] Detected 2014.921 MHz processor.
[ 12.528383] Built 1 zonelists. Total pages: 65009
[ 12.528391] Kernel command line: root=UUID=5c8d9581-9cec-424d-a1ee-c24fa7d79613 ro quiet splash
[ 12.528602] mapped APIC to ffffd000 (fee00000)
[ 12.528606] mapped IOAPIC to ffffc000 (fec00000)
[ 12.528610] Enabling fast FPU save and restore... done.
[ 12.528615] Enabling unmasked SIMD FPU exception support... done.
[ 12.528628] Initializing CPU#0
[ 12.528718] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 12.530091] Console: colour VGA+ 80x25
[ 12.530271] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 12.530478] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 12.536985] Memory: 248888k/262080k available (1993k kernel code, 12700k reserved, 900k data, 328k init, 0k highmem)
[ 12.536998] virtual kernel memory layout:
[ 12.536999] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 12.537001] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 12.537002] vmalloc : 0xd0800000 - 0xff7fe000 ( 751 MB)
[ 12.537004] lowmem : 0xc0000000 - 0xcfff0000 ( 255 MB)
[ 12.537005] .init : 0xc03d9000 - 0xc042b000 ( 328 kB)
[ 12.537006] .data : 0xc02f2429 - 0xc03d36d4 ( 900 kB)
[ 12.537008] .text : 0xc0100000 - 0xc02f2429 (1993 kB)
[ 12.537012] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 12.616686] Calibrating delay using timer specific routine.. 4033.11 BogoMIPS (lpj=8066229)
[ 12.616755] Security Framework v1.0.0 initialized
[ 12.616765] SELinux: Disabled at boot.
[ 12.616795] Mount-cache hash table entries: 512
[ 12.617046] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00000400 00000000 00000000
[ 12.617066] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 12.617070] CPU: L2 cache: 128K
[ 12.617074] CPU: Hyper-Threading is disabled
[ 12.617077] CPU: After all inits, caps: bfebfbff 00000000 00000000 00003080 00000400 00000000 00000000
[ 12.617096] Compat vDSO mapped to ffffe000.
[ 12.617101] Remapping vsyscall page to ffffe000
[ 12.617121] Checking 'hlt' instruction... OK.
[ 12.632824] SMP alternatives: switching to UP code
[ 12.633182] Freeing SMP alternatives: 11k freed
[ 12.633500] Early unpacking initramfs... done
[ 13.042500] ACPI: Core revision 20060707
[ 13.043994] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT.
[ 13.101254] CPU0: Intel(R) Celeron(R) CPU 2.00GHz stepping 07
[ 13.101314] Total of 1 processors activated (4033.11 BogoMIPS).
[ 13.101429] ENABLING IO-APIC IRQs
[ 13.101631] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 13.248512] Brought up 1 CPUs
[ 13.248925] Booting paravirtualized kernel on bare hardware
[ 13.249102] Time: 18:57:28 Date: 09/11/107
[ 13.249155] NET: Registered protocol family 16
[ 13.249388] EISA bus registered
[ 13.249403] ACPI: bus type pci registered
[ 13.252640] PCI: PCI BIOS revision 2.10 entry at 0xfdb31, last bus=2
[ 13.252643] PCI: Using configuration type 1
[ 13.252646] Setting up standard PCI resources
[ 13.266432] ACPI: Interpreter enabled
[ 13.266441] ACPI: Using IOAPIC for interrupt routing
[ 13.267574] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 13.267584] PCI: Probing PCI hardware (bus 00)
[ 13.268848] Enabling SiS 96x SMBus.
[ 13.269645] Boot video device is 0000:01:00.0
[ 13.269731] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 13.278500] ACPI: Power Resource [URP1] (off)
[ 13.278703] ACPI: Power Resource [URP2] (off)
[ 13.278903] ACPI: Power Resource [FDDP] (off)
[ 13.279113] ACPI: Power Resource [LPTP] (off)
[ 13.282060] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 12 14 15)
[ 13.282542] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 13.283023] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 13.283494] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 13.283991] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 13.284495] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 13.284983] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 *12 14 15)
[ 13.285459] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 *12 14 15)
[ 13.285741] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 13.285778] pnp: PnP ACPI init
[ 13.292644] pnp: PnP ACPI: found 12 devices
[ 13.292654] PnPBIOS: Disabled by ACPI PNP
[ 13.292788] PCI: Using ACPI for IRQ routing
[ 13.292795] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 13.308278] NET: Registered protocol family 8
[ 13.308282] NET: Registered protocol family 20
[ 13.309534] PCI: Bridge: 0000:00:01.0
[ 13.309540] IO window: disabled.
[ 13.309548] MEM window: ddd00000-dfefffff
[ 13.309554] PREFETCH window: cd900000-ddbfffff
[ 13.309617] NET: Registered protocol family 2
[ 13.344507] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 13.344663] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 13.344726] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 13.344762] TCP: Hash tables configured (established 8192 bind 4096)
[ 13.344766] TCP reno registered
[ 13.356598] checking if image is initramfs... it is
[ 14.138222] Freeing initrd memory: 6748k freed
[ 14.139267] audit: initializing netlink socket (disabled)
[ 14.139292] audit(1192129048.636:1): initialized
[ 14.139592] VFS: Disk quotas dquot_6.5.1
[ 14.139626] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 14.139730] io scheduler noop registered
[ 14.139736] io scheduler anticipatory registered
[ 14.139739] io scheduler deadline registered
[ 14.139764] io scheduler cfq registered (default)
[ 14.140343] isapnp: Scanning for PnP cards...
[ 14.494312] isapnp: No Plug & Play device found
[ 14.637331] Real Time Clock Driver v1.12ac
[ 14.637480] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 14.637697] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 14.638192] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 14.640242] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 14.640995] 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 14.641786] mice: PS/2 mouse device common for all mice
[ 14.643633] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 14.644046] input: Macintosh mouse button emulation as /class/input/input0
[ 14.644161] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 14.644170] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 14.644637] PNP: PS/2 Controller [PNP030b:PS2K] at 0x60,0x64 irq 1
[ 14.644642] PNP: PS/2 controller doesn't have AUX irq; using default 12
[ 14.647372] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 14.647749] EISA: Probing bus 0 at eisa.0
[ 14.647890] EISA: Detected 0 cards.
[ 14.678029] TCP cubic registered
[ 14.678045] NET: Registered protocol family 1
[ 14.678083] Using IPI No-Shortcut mode
[ 14.678280] ACPI: (supports S0 S1 S4 S5)
[ 14.678359] Magic number: 11:203:999
[ 14.678390] hash matches device ttyaf
[ 14.678581] hash matches device 00:01
[ 14.678584] hash matches device pnp0
[ 14.679052] Freeing unused kernel memory: 328k freed
[ 14.679811] Time: tsc clocksource has been installed.
[ 16.211916] Capability LSM initialized
[ 17.452773] usbcore: registered new interface driver usbfs
[ 17.452820] usbcore: registered new interface driver hub
[ 17.452900] usbcore: registered new device driver usb
[ 17.454233] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 17.454304] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 16
[ 17.454327] ohci_hcd 0000:00:03.0: OHCI Host Controller
[ 17.454576] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
[ 17.454608] ohci_hcd 0000:00:03.0: irq 16, io mem 0xdfffc000
[ 17.596665] usb usb1: configuration #1 chosen from 1 choice
[ 17.596730] hub 1-0:1.0: USB hub found
[ 17.596747] hub 1-0:1.0: 2 ports detected
[ 17.615612] dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
[ 17.702584] ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 17
[ 17.702610] ohci_hcd 0000:00:03.1: OHCI Host Controller
[ 17.702672] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
[ 17.702699] ohci_hcd 0000:00:03.1: irq 17, io mem 0xdfffd000
[ 17.730607] Floppy drive(s): fd0 is 1.44M
[ 17.754096] FDC 0 is a post-1991 82077
[ 17.764504] usb usb2: configuration #1 chosen from 1 choice
[ 17.764570] hub 2-0:1.0: USB hub found
[ 17.764589] hub 2-0:1.0: 2 ports detected
[ 17.870485] ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 18
[ 17.870513] ohci_hcd 0000:00:03.2: OHCI Host Controller
[ 17.870572] ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
[ 17.870601] ohci_hcd 0000:00:03.2: irq 18, io mem 0xdfffe000
[ 17.932403] usb usb3: configuration #1 chosen from 1 choice
[ 17.932475] hub 3-0:1.0: USB hub found
[ 17.932496] hub 3-0:1.0: 2 ports detected
[ 18.040380] SIS5513: IDE controller at PCI slot 0000:00:02.5
[ 18.040407] SIS5513: chipset revision 0
[ 18.040410] SIS5513: not 100% native mode: will probe irqs later
[ 18.040430] SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
[ 18.040450] ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
[ 18.040471] ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA
[ 18.040486] Probing IDE interface ide0...
[ 18.330198] hda: Maxtor 2F030J0, ATA DISK drive
[ 18.346039] usb 3-1: new low speed USB device using ohci_hcd and address 2
[ 18.564139] usb 3-1: configuration #1 chosen from 1 choice
[ 18.614066] hdb: SAMSUNG SV1022D, ATA DISK drive
[ 18.670149] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 20.240950] Probing IDE interface ide1...
[ 20.980984] hdc: Optiarc DVD RW AD-7173A, ATAPI CD/DVD-ROM drive
[ 21.652710] ide1 at 0x170-0x177,0x376 on irq 15
[ 21.663788] ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 19
[ 21.663815] ehci_hcd 0000:00:03.3: EHCI Host Controller
[ 21.664194] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
[ 21.664258] PCI: cache line size of 128 is not supported by device 0000:00:03.3
[ 21.664280] ehci_hcd 0000:00:03.3: irq 19, io mem 0xdffff000
[ 21.664290] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 21.664342] usb 3-1: USB disconnect, address 2
[ 21.667514] usb usb4: configuration #1 chosen from 1 choice
[ 21.667574] hub 4-0:1.0: USB hub found
[ 21.667594] hub 4-0:1.0: 6 ports detected
[ 21.674595] SCSI subsystem initialized
[ 21.689176] libata version 2.20 loaded.
[ 21.772809] ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 17 (level, low) -> IRQ 20
[ 21.795889] eth0: Davicom DM9102 at pci0000:00:06.0, 00:08:a1:2c:06:bf, irq 20.
[ 21.840281] hda: max request size: 128KiB
[ 21.850042] hda: 60058656 sectors (30750 MB) w/2048KiB Cache, CHS=59582/16/63, UDMA(133)
[ 21.866533] hda: cache flushes supported
[ 21.866601] hda: hda1 hda2 < hda5 >
[ 21.955904] hdb: max request size: 128KiB
[ 21.957520] hdb: 19931184 sectors (10204 MB) w/472KiB Cache, CHS=19773/16/63, UDMA(66)
[ 21.957532] hdb: cache flushes not supported
[ 21.957613] hdb: hdb1
[ 21.971432] hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 21.971446] Uniform CD-ROM driver Revision: 3.20
[ 22.005667] usbcore: registered new interface driver hiddev
[ 22.284216] usb 3-1: new low speed USB device using ohci_hcd and address 3
[ 22.500897] kjournald starting. Commit interval 5 seconds
[ 22.500922] EXT3-fs: mounted filesystem with ordered data mode.
[ 22.502479] usb 3-1: configuration #1 chosen from 1 choice
[ 22.517505] input: HID 1241:1166 as /class/input/input1
[ 22.517550] input: USB HID v1.10 Mouse [HID 1241:1166] on usb-0000:00:03.2-1
[ 22.517574] usbcore: registered new interface driver usbhid
[ 22.517579] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 37.617937] NET: Registered protocol family 17
[ 39.220005] Linux agpgart interface v0.102 (c) Dave Jones
[ 39.497356] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x0c00
[ 39.497563] agpgart: Detected SiS 646 chipset
[ 39.502193] agpgart: AGP aperture is 64M @ 0xe0000000
[ 39.666633] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 39.678326] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 39.979991] input: PC Speaker as /class/input/input2
[ 40.182384] parport: PnPBIOS parport detected.
[ 40.182501] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 40.215798] parport0: Printer, Hewlett-Packard HP LaserJet 5L
[ 40.418088] nvidia: module license 'NVIDIA' taints kernel.
[ 40.824186] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 21
[ 40.825019] NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-9631 Thu Nov 9 17:38:10 PST 2006
[ 40.965057] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 22
[ 41.287242] intel8x0_measure_ac97_clock: measured 56814 usecs
[ 41.287248] intel8x0: clocking to 48000
[ 41.544672] lp0: using parport0 (interrupt-driven).
[ 41.625373] fuse init (API version 7.Cool
[ 41.717483] Adding 746980k swap on /dev/disk/by-uuid/cb0973a5-4817-45d4-8ad8-015289c99c1b. Priority:-1 extents:1 across:746980k
[ 41.813577] EXT3 FS on hda1, internal journal
[ 42.264610] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 47.045281] NET: Registered protocol family 10
[ 47.045471] lo: Disabled Privacy Extensions
[ 48.637946] input: Power Button (FF) as /class/input/input3
[ 48.646019] ACPI: Power Button (FF) [PWRF]
[ 48.697591] input: Power Button (CM) as /class/input/input4
[ 48.705661] ACPI: Power Button (CM) [PWRB]
[ 48.734926] Using specific hotkey driver
[ 48.784136] No dock devices found.
[ 48.855268] ibm_acpi: ec object not found
[ 49.055959] pcc_acpi: loading...
[ 52.256581] ppdev: user-space parallel port driver
[ 54.178897] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 54.178930] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 54.178988] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[ 55.574960] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 55.574969] apm: overridden by ACPI.
[ 67.570253] input: AT Translated Set 2 keyboard as /class/input/input5
[ 133.088047] eth0: no IPv6 routers present
[ 1075.980402] usb 4-5: new high speed USB device using ehci_hcd and address 3
[ 1076.113425] usb 4-5: configuration #1 chosen from 1 choice
[ 1076.958917] usbcore: registered new interface driver libusual
[ 1077.195337] Initializing USB Mass Storage driver...
[ 1077.199780] scsi0 : SCSI emulation for USB Mass Storage devices
[ 1077.201090] usb-storage: device found at 3
[ 1077.201098] usb-storage: waiting for device to settle before scanning
[ 1077.201677] usbcore: registered new interface driver usb-storage
[ 1077.201949] USB Mass Storage support registered.
[ 1082.197746] usb-storage: device scan complete
[ 1083.373739] scsi 0:0:0:0: Direct-Access USB 2.0 Flash Disk 1.00 PQ: 0 ANSI: 2
[ 1083.425304] SCSI device sda: 3964928 512-byte hdwr sectors (2030 MB)
[ 1083.426429] sda: Write Protect is off
[ 1083.426437] sda: Mode Sense: 03 00 00 00
[ 1083.426440] sda: assuming drive cache: write through
[ 1083.429765] SCSI device sda: 3964928 512-byte hdwr sectors (2030 MB)
[ 1083.430801] sda: Write Protect is off
[ 1083.430809] sda: Mode Sense: 03 00 00 00
[ 1083.430812] sda: assuming drive cache: write through
[ 1083.431651] sda: unknown partition table
[ 1083.434646] sd 0:0:0:0: Attached scsi removable disk sda
[ 1083.454721] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1113.494748] usb 4-5: reset high speed USB device using ehci_hcd and address 3
[ 1116.625273] usb 4-5: device descriptor read/64, error -110
[ 1131.834126] usb 4-5: device descriptor read/64, error -110
[ 1132.050026] usb 4-5: reset high speed USB device using ehci_hcd and address 3
[ 1135.160571] usb 4-5: device descriptor read/64, error -110
meiekaks@meiekaks:~$

Selline see dmesg väljund on


nick
Pingviini kasutaja
Pingviini kasutaja



Liitunud: 01.08.2005
Postitused: 39
Asukoht: Tartu
Distributsioon: Gentoo/FreeBSD/Xubuntu
estonia.gif
postituspostitatud: 11.10.2007, 21:26  postituse pealkiri:  (teema puudub)  

[ 1083.431651] sda: unknown partition table

mida näitab: fdisk -l /dev/sda


maq
Pingviini aktivist
Pingviini aktivist



Liitunud: 16.08.2005
Postitused: 162

Distributsioon: Kubuntu 13.10
estonia.gif
postituspostitatud: 11.10.2007, 21:36  postituse pealkiri:  (teema puudub)  

Kui pulk on järgi ja ühendus olemas siis näitas järgmist asja:
meiekaks@meiekaks:~$ fdisk -l /dev/sda

Disk /dev/sda: 2030 MB, 2030043136 bytes
63 heads, 62 sectors/track, 1015 cylinders
Units = silindrit of 3906 * 512 = 1999872 bytes

This doesn't look like a partition table
Probably you selected the wrong device.

Seade Boot Start End Blocks Id System
/dev/sda1 ? 199216 491461 570754815+ 72 Tundmatu
Partitsiooni 1 füüsiline ja loogiline algus ei lange kokku:
(Pole Linuxi oma?)
füüs=(357, 116, 40) loogiline=(199215, 34, 11)
Partitsiooni 1 füüsiline ja loogiline lõpp ei lange kokku:
füüs=(357, 32, 45) loogiline=(491460, 44, 51)
Partition 1 does not end on cylinder boundary.
/dev/sda2 ? 43188 538843 968014120 65 Novell Netware 386
Partitsiooni 2 füüsiline ja loogiline algus ei lange kokku:
(Pole Linuxi oma?)
füüs=(288, 115, 43) loogiline=(43187, 17, 47)
Partitsiooni 2 füüsiline ja loogiline lõpp ei lange kokku:
füüs=(367, 114, 50) loogiline=(538842, 14, 42)
Partition 2 does not end on cylinder boundary.
/dev/sda3 ? 478721 974376 968014096 79 Tundmatu
Partitsiooni 3 füüsiline ja loogiline algus ei lange kokku:
(Pole Linuxi oma?)
füüs=(366, 32, 33) loogiline=(478720, 18, 30)
Partitsiooni 3 füüsiline ja loogiline lõpp ei lange kokku:
füüs=(357, 32, 43) loogiline=(974375, 14, 39)
Partition 3 does not end on cylinder boundary.
/dev/sda4 ? 1 931190 1818613248 d Tundmatu
Partitsiooni 4 füüsiline ja loogiline algus ei lange kokku:
(Pole Linuxi oma?)
füüs=(372, 97, 50) loogiline=(0, 0, 1)
Partitsiooni 4 füüsiline ja loogiline lõpp ei lange kokku:
füüs=(0, 10, 0) loogiline=(931189, 36, 30)
Partition 4 does not end on cylinder boundary.

Partitsioonitabeli kirjed on füüsilisest erinevas järjekorras


nick
Pingviini kasutaja
Pingviini kasutaja



Liitunud: 01.08.2005
Postitused: 39
Asukoht: Tartu
Distributsioon: Gentoo/FreeBSD/Xubuntu
estonia.gif
postituspostitatud: 11.10.2007, 21:45  postituse pealkiri:  (teema puudub)  

Partitsiooni tabel on sassi läinud.

Järgenvat võid teha, kui andmed mälupulgal ei ole olulised:

fdisk /dev/sda

d - kustuta partitsioon
1 (Partition number) kuni 4

p - näita hetke seisu (ühtegi partitsiooni ei tohi enam olla, kui on, siis kustuta ka need ära)

n - uus partitsioon

t - muuda süsteemi ID
c - teha fat partitsioon

w - salvesta muudatused

mkdosfs /dev/sda1 (teeb fat ketta valmis)

võta pulk küljest ära ja uuesti külge.


maq
Pingviini aktivist
Pingviini aktivist



Liitunud: 16.08.2005
Postitused: 162

Distributsioon: Kubuntu 13.10
estonia.gif
postituspostitatud: 11.10.2007, 22:12  postituse pealkiri:  (teema puudub)  

Mnjh... Tahaks neid asju sealt mälupulgalt kuidagi kätte saada.


nick
Pingviini kasutaja
Pingviini kasutaja



Liitunud: 01.08.2005
Postitused: 39
Asukoht: Tartu
Distributsioon: Gentoo/FreeBSD/Xubuntu
estonia.gif
postituspostitatud: 11.10.2007, 22:28  postituse pealkiri:  (teema puudub)  

vaata seda: http://pingviin.org/viewtopic.php?t=3714&highlight=


maq
Pingviini aktivist
Pingviini aktivist



Liitunud: 16.08.2005
Postitused: 162

Distributsioon: Kubuntu 13.10
estonia.gif
postituspostitatud: 12.10.2007, 18:08  postituse pealkiri:  (teema puudub)  

Pulgale asju panna saan, aga kui hakkan neid sealt arvutisse kopima siis läheb andmete kopeerimis kiirus kiiresti nulli ja ühendus kaob. Imelik aga, et wundowsi all töötab sama mälupulk täiesti perfektselt.


johnsmith
Vana Pingviin
Vana Pingviin


Vanus: 49
Liitunud: 24.07.2006
Postitused: 714
Asukoht: Universum
Distributsioon: Ubuntu/Gentoo/FreeBSD
finland.gif
postituspostitatud: 12.10.2007, 22:51  postituse pealkiri:  (teema puudub)  

No krt, füüsilised ja loogilised ketta geomeetrilised andmed on ju kirjutatud partitsiooni tabelisse kui see on korrumpeerunud siis ei tea ju ka windoosa kus algab partitsioon ja kus lõpeb.

Järelikult partitsiooni tabel on korras aga kasutab mingit windowsis toimivat formaati mis ei ole standard.

MS -i vandenõu Surprised

_________________
"Thinking is the hardest work there is, which is probably the reason why so few engage in it" - Henry Ford

maq
Pingviini aktivist
Pingviini aktivist



Liitunud: 16.08.2005
Postitused: 162

Distributsioon: Kubuntu 13.10
estonia.gif
postituspostitatud: 12.10.2007, 23:26  postituse pealkiri:  (teema puudub)  

mnjh... tegin nii nagu nick õpetas. Nüüd näitab fdisk -l /dev/sda peale, et küljes on fat32 failisüsteemiga pulk., aga sama jama jätkub ikka. Sad Kas tõepoolest polegi võimalik seda mälupulka kasutada linux-is. :O


spott
Admin
Admin


Vanus: 43
Liitunud: 04.06.2005
Postitused: 8853

Distributsioon: Ubuntu
estonia.gif
postituspostitatud: 13.10.2007, 07:41  postituse pealkiri:  (teema puudub)  

Ühenda käsitsi ja vaata, kas siis sama jama:
sudo mkdir /media/usb
sudo mount -t vfat /dev/sda /media/usb
Ja vaata, kas siis jääb külge.

Lisaks - võid mõelda ka kerneli või siis kogu distributsiooni uuendamise peale.

_________________
Tellige endale sünnipäevaks, sõbrapäevaks või muuks tähtpäevaks kingitus: Kingitused internetist - NetiKink.eu

maq
Pingviini aktivist
Pingviini aktivist



Liitunud: 16.08.2005
Postitused: 162

Distributsioon: Kubuntu 13.10
estonia.gif
postituspostitatud: 15.10.2007, 19:27  postituse pealkiri:  (teema puudub)  

spott mõne päeva pärast uuendangi Kubunt 7.10 peale oma Kubuntu. Smile


maq
Pingviini aktivist
Pingviini aktivist



Liitunud: 16.08.2005
Postitused: 162

Distributsioon: Kubuntu 13.10
estonia.gif
postituspostitatud: 26.10.2007, 16:52  postituse pealkiri:  (teema puudub)  

mnjh nüüd on mul masinas siis kubuntu 7.10, aga probleem on ikka sama. Sad
Pulgalt arvutisse faile kopidas ei saa. Hakkab ilusasti kopeerima ja natukese aja pärast ühenduse kiirus seiskub ja kogu lugu.


indrek
Vana Pingviin
Vana Pingviin


Vanus: 45
Liitunud: 08.07.2005
Postitused: 412
Asukoht: Tallinn
Distributsioon: Kubuntu
blank.gif
postituspostitatud: 26.10.2007, 21:26  postituse pealkiri:  (teema puudub)  

Proovi usb2.0 disableda ning seejärel kopeerida:
sudo modprobe -r ehci_hcd

Kui see aitab, siis tuleks hakata probleemi otsima - kas ei toeta linux korralikult su emaplaadi chipsetti või äkki hakkab emaplaat otsi andma (osadel vanadel thinkpadidel algab see just niimoodi).


maq
Pingviini aktivist
Pingviini aktivist



Liitunud: 16.08.2005
Postitused: 162

Distributsioon: Kubuntu 13.10
estonia.gif
postituspostitatud: 18.04.2008, 22:08  postituse pealkiri:  (teema puudub)  

mälupulka arvuti taha pannes viskab sellist veateadet :cannot obtain lock on /media/.hal-mtab mis see tähendab?


spott
Admin
Admin


Vanus: 43
Liitunud: 04.06.2005
Postitused: 8853

Distributsioon: Ubuntu
estonia.gif
postituspostitatud: 19.04.2008, 09:51  postituse pealkiri:  (teema puudub)  

Vaata Autofs seadeid.

https://help.ubuntu.com/community/Autofs

_________________
Tellige endale sünnipäevaks, sõbrapäevaks või muuks tähtpäevaks kingitus: Kingitused internetist - NetiKink.eu

maq
Pingviini aktivist
Pingviini aktivist



Liitunud: 16.08.2005
Postitused: 162

Distributsioon: Kubuntu 13.10
estonia.gif
postituspostitatud: 24.04.2008, 22:35  postituse pealkiri:  (teema puudub)  

mnjh ausaltöelda ei saa ma mitte midagi aru mis seal seadetes tegema peaks. Sad


Näita (aja järgi):      
Postita uus teemaVasta teemale


Vaata järgmist teemat
Vaata eelmist teemat
Powered by phpBB2 Plus based on phpBB © 2001/7 phpBB Group