sudo smartctl -a /dev/sda
smartctl 6.2 2013-04-20 r3812 [x86_64-linux-3.11.0-12-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke,
www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Blue Serial ATA
Device Model: WDC WD5000AAKS-65A7B0
Serial Number: WD-WMASY1823803
LU WWN Device Id: 5 0014ee 0ab60da62
Firmware Version: 01.03B01
User Capacity: 500 107 862 016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.5, 3.0 Gb/s
Local Time is: Fri Dec 19 11:57:49 2014 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (10800) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 127) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 190 154 021 Pre-fail Always - 3458
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2724
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 051 Old_age Always - 0
9 Power_On_Hours 0x0032 055 055 000 Old_age Always - 33115
10 Spin_Retry_Count 0x0032 100 100 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 504
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 165
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 2234
194 Temperature_Celsius 0x0022 108 093 000 Old_age Always - 39
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 051 Old_age Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 8 inconsistent with error log pointer 1
ATA Error Count: 8 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 8 occurred at disk power-on lifetime: 33096 hours (1379 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 d6 ba 04 e1 Error: UNC at LBA = 0x0104bad6 = 17087190
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 d0 ba 04 01 08 00:53:36.396 READ DMA
c8 00 08 a0 0b 00 00 08 00:53:36.395 READ DMA
c8 00 80 d8 ba 04 01 08 00:53:36.381 READ DMA
ec 00 00 00 00 00 00 08 00:53:36.372 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 00:53:36.365 SET FEATURES [Set transfer mode]
Error 7 occurred at disk power-on lifetime: 33096 hours (1379 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 d6 ba 04 e1 Error: UNC at LBA = 0x0104bad6 = 17087190
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 98 ba 04 01 08 00:53:33.440 READ DMA
c8 00 08 98 0b 00 00 08 00:53:33.440 READ DMA
c8 00 20 78 ba 04 01 08 00:53:33.440 READ DMA
c8 00 08 90 0b 00 00 08 00:53:33.440 READ DMA
c8 00 08 70 ba 04 01 08 00:53:33.439 READ DMA
Error 6 occurred at disk power-on lifetime: 33096 hours (1379 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 d6 ba 04 e1 Error: UNC at LBA = 0x0104bad6 = 17087190
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 f0 80 ba 04 01 08 00:43:52.768 READ DMA
c8 00 08 78 ba 04 01 08 00:43:52.768 READ DMA
c8 00 08 70 ba 04 01 08 00:43:52.768 READ DMA
c8 00 f0 58 b9 04 01 08 00:43:52.766 READ DMA
c8 00 08 50 b9 04 01 08 00:43:52.766 READ DMA
Error 5 occurred at disk power-on lifetime: 33096 hours (1379 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 d6 ba 04 e1 Error: UNC at LBA = 0x0104bad6 = 17087190
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 f0 80 ba 04 01 08 00:41:11.767 READ DMA
c8 00 08 78 ba 04 01 08 00:41:11.767 READ DMA
c8 00 08 70 ba 04 01 08 00:41:11.766 READ DMA
c8 00 f0 58 b9 04 01 08 00:41:11.765 READ DMA
c8 00 08 50 b9 04 01 08 00:41:11.765 READ DMA
Error 4 occurred at disk power-on lifetime: 33096 hours (1379 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 d6 ba 04 e1 Error: UNC at LBA = 0x0104bad6 = 17087190
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 f0 80 ba 04 01 08 00:38:05.400 READ DMA
c8 00 08 78 ba 04 01 08 00:38:05.399 READ DMA
c8 00 08 70 ba 04 01 08 00:38:05.399 READ DMA
c8 00 f0 58 b9 04 01 08 00:38:05.398 READ DMA
c8 00 08 50 b9 04 01 08 00:38:05.397 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
