Ubuntu Inteli draiveritega ei lülita monitori välja

[estysoft]

Mul on NUC6i5SYH Ubuntu 16.04 64bit.
Soov on et screensaverit ei ole ja monitor lülitatakse 30 minuti möödumisel välja. Arvuti päris magama ei peaks jääma.

Muu nagu toimib aga monitor jääb vilkuma.


Kuidas ma debugin milles asi on?
Graafilistest menüüdest olen screensaverid välja lülitanud brightens and locki alt on aeg määratud.

http://www.intel.com/content/www/us/en/ ... i5syh.html

[vooler3]

Mul on NUC6i5SYH Ubuntu 16.04 64bit.
Soov on et screensaverit ei ole ja monitor lülitatakse 30 minuti möödumisel välja. Arvuti päris magama ei peaks jääma.

Muu nagu toimib aga monitor jääb vilkuma.


Kuidas ma debugin milles asi on?
Graafilistest menüüdest olen screensaverid välja lülitanud brightens and locki alt on aeg määratud.

http://www.intel.com/content/www/us/en/ ... i5syh.html

Windows-based "masinatega" kaasnevad röömud ja kurbused kuna pole olemas õiget videodraiverit Linuxiga töötamiseks.

Igatahes netis on näha ainult üks soovitus: pead ise toitenupust lõplikult välja lülitama.

Poweroff
After issuing a shutdown, the NUC might remain in some state which isn't completely shut down, as indicated by a remaining blue power LED. In this case it's neccesary to power off the unit by holding the power button for a few seconds.

The workaround for this issue is to disable all wake-on-CIR (infrared sensor) options in the BIOS. In some cases it might be required to disable the CIR sensor completely to fix the issue.

https://wiki.archlinux.org/index.php/Intel_NUC

[DaStoned]

Probleem tundub olevat monitori, mitte arvuti välja lülitamises.

Mis monitor sul on ja mida tähendab "jääb vilkuma"?

Sealtsamast on mingid viited inteli draiveri toite konfigureerimiseks, kuigi see tundub käivat videokaardi enda kohta, mitte monitori kohta:
https://wiki.archlinux.org/index.php/In ... ng_Options

[estysoft]

Ma alustasin siis sellega et uuesndasin ubuntu 16.10 peale seal on uus kernel kus pidi mitmeid teemakohaseid parandusi olema. Eks näeb kas see juba aitab.

Samsung U28E590D on ühendatud displayporti kaudu.
Vilkumine tähendaks midagi sellist, et arvuti äratab monitori iga ~10 sekundi tagant hetkeks üles.


Saan aru et mul on ainult enable_hangcheck lubatud. Proovisin lisada /etc/modprobe.d/i915.conf. Sisuga options i915 enable_dc=1
Aga peale restarti jääb väljund samaks.

Kood: Vali kõik

elgar@NUC5:~$ modinfo -p i915
modeset:Use kernel modesetting [KMS] (0=disable, 1=on, -1=force vga console preference [default]) (int)
panel_ignore_lid:Override lid status (0=autodetect, 1=autodetect disabled [default], -1=force lid closed, -2=force lid open) (int)
semaphores:Use semaphores for inter-ring sync (default: -1 (use per-chip defaults)) (int)
enable_rc6:Enable power-saving render C-state 6. Different stages can be selected via bitmask values (0 = disable; 1 = enable rc6; 2 = enable deep rc6; 4 = enable deepest rc6). For example, 3 would enable rc6 and deep rc6, and 7 would enable everything. default: -1 (use per-chip default) (int)
enable_dc:Enable power-saving display C-states. (-1=auto [default]; 0=disable; 1=up to DC5; 2=up to DC6) (int)
enable_fbc:Enable frame buffer compression for power savings (default: -1 (use per-chip default)) (int)
lvds_channel_mode:Specify LVDS channel mode (0=probe BIOS [default], 1=single-channel, 2=dual-channel) (int)
lvds_use_ssc:Use Spread Spectrum Clock with panels [LVDS/eDP] (default: auto from VBT) (int)
vbt_sdvo_panel_type:Override/Ignore selection of SDVO panel mode in the VBT (-2=ignore, -1=auto [default], index in VBT BIOS table) (int)
reset:Attempt GPU resets (default: true) (bool)
enable_hangcheck:Periodically check GPU activity for detecting hangs. WARNING: Disabling this can cause system wide hangs. (default: true) (bool)
enable_ppgtt:Override PPGTT usage. (-1=auto [default], 0=disabled, 1=aliasing, 2=full, 3=full with extended address space) (int)
enable_execlists:Override execlists usage. (-1=auto [default], 0=disabled, 1=enabled) (int)
enable_psr:Enable PSR (0=disabled, 1=enabled - link mode chosen per-platform, 2=force link-standby mode, 3=force link-off mode) Default: -1 (use per-chip default) (int)
preliminary_hw_support:Enable preliminary hardware support. (int)
disable_power_well:Disable display power wells when possible (-1=auto [default], 0=power wells always on, 1=power wells disabled when possible) (int)
enable_ips:Enable IPS (default: true) (int)
fastboot:Try to skip unnecessary mode sets at boot time (default: false) (bool)
prefault_disable:Disable page prefaulting for pread/pwrite/reloc (default:false). For developers only. (bool)
load_detect_test:Force-enable the VGA load detect code for testing (default:false). For developers only. (bool)
invert_brightness:Invert backlight brightness (-1 force normal, 0 machine defaults, 1 force inversion), please report PCI device ID, subsystem vendor and subsystem device ID to dri-devel@lists.freedesktop.org, if your machine needs it. It will then be included in an upcoming module version. (int)
disable_display:Disable display (default: false) (bool)
enable_cmd_parser:Enable command parsing (1=enabled [default], 0=disabled) (int)
use_mmio_flip:use MMIO flips (-1=never, 0=driver discretion [default], 1=always) (int)
mmio_debug:Enable the MMIO debug code for the first N failures (default: off). This may negatively affect performance. (int)
verbose_state_checks:Enable verbose logs (ie. WARN_ON()) in case of unexpected hw state conditions. (bool)
nuclear_pageflip:Force atomic modeset functionality; asynchronous mode is not yet supported. (default: false). (bool)
edp_vswing:Ignore/Override vswing pre-emph table selection from VBT (0=use value from vbt [default], 1=low power swing(200mV),2=default swing(400mV)) (int)
enable_guc_loading:Enable GuC firmware loading (-1=auto, 0=never [default], 1=if available, 2=required) (int)
enable_guc_submission:Enable GuC submission (-1=auto, 0=never [default], 1=if available, 2=required) (int)
guc_log_level:GuC firmware logging level (-1:disabled (default), 0-3:enabled) (int)
enable_dp_mst:Enable multi-stream transport (MST) for new DisplayPort sinks. (default: true) (bool)
inject_load_failure:Force an error after a number of failure check points (0:disabled (default), N:force failure at the Nth failure check point) (uint)
enable_dpcd_backlight:Enable support for DPCD backlight control (default:false) (bool)
enable_gvt:Enable support for Intel GVT-g graphics virtualization host support(default:false) (bool)
elgar@NUC5:~$ systool -m i915 -av
Module = "i915"

  Attributes:
    coresize            = "1314816"
    initsize            = "0"
    initstate           = "live"
    refcnt              = "234"
    srcversion          = "EA783CE84299ECD1829866F"
    taint               = ""
    uevent              = <store method only>

  Parameters:
    enable_hangcheck    = "Y"

  Sections:
    .altinstr_aux       = "0x0000000000000000"
    .altinstr_replacement= "0x0000000000000000"
    .altinstructions    = "0x0000000000000000"
    .bss                = "0x0000000000000000"
    .data..read_mostly  = "0x0000000000000000"
    .data.unlikely      = "0x0000000000000000"
    .data               = "0x0000000000000000"
    .exit.text          = "0x0000000000000000"
    .fixup              = "0x0000000000000000"
    .gnu.linkonce.this_module= "0x0000000000000000"
    .init.text          = "0x0000000000000000"
    .note.gnu.build-id  = "0x0000000000000000"
    .parainstructions   = "0x0000000000000000"
    .ref.data           = "0x0000000000000000"
    .rodata.str1.1      = "0x0000000000000000"
    .rodata.str1.8      = "0x0000000000000000"
    .rodata             = "0x0000000000000000"
    .smp_locks          = "0x0000000000000000"
    .strtab             = "0x0000000000000000"
    .symtab             = "0x0000000000000000"
    .text               = "0x0000000000000000"
    .text.unlikely      = "0x0000000000000000"
    __bug_table         = "0x0000000000000000"
    __ex_table          = "0x0000000000000000"
    __jump_table        = "0x0000000000000000"
    __kcrctab_gpl       = "0x0000000000000000"
    __ksymtab_gpl       = "0x0000000000000000"
    __ksymtab_strings   = "0x0000000000000000"
    __mcount_loc        = "0x0000000000000000"
    __param             = "0x0000000000000000"
    __tracepoints_ptrs  = "0x0000000000000000"
    __tracepoints       = "0x0000000000000000"
    __tracepoints_strings= "0x0000000000000000"
    _ftrace_events      = "0x0000000000000000"

[DaStoned]

Proovi HDMI-d, ma olen märganud et see on stabiilsem.