1. leht 2-st
Ubuntu 6.06 ja mx700 küljenupud
Postitatud: 27.05.2006, 14:18
Postitas digweed
5.10 piisas kui xorg muuta selliseks:
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/input/mice"
Option "Protocol" "ExplorerPS/2"
Option "Buttons" "7"
Option "ZAxisMapping" "4 5"
EndSection
6.06 ei toimi halli kottigi
wm gnome
Postitatud: 27.05.2006, 15:27
Postitas Innu
Section "InputDevice"
Identifier "Configured Mouse"
Driver "evdev"
Option "CorePointer"
Option "Device" "/dev/input/event1"
Option "Dev Name" "Logitech USB-PS/2 Optical Mouse"
Option "Resolution" "800"
Option "Buttons" "10"
Option "ZAxisMapping" "9 10"
Option "Dev Phys" "usb-*/input0"
EndSection
Mx518 ja nii toimib hiir mul täielikult.
Postitatud: 27.05.2006, 15:30
Postitas digweed
leidisn ubuntust sama kuid x ei länud tööle.
Option "Dev Name" muutsin vastavalt mx700`le.
Postitatud: 27.05.2006, 15:49
Postitas vih
Ja mis error siis tuli? /var/log/Xorg.log vms fail.
Muide Gnome on Desktop Environment, see siis natuke rohkem kui Window Manager. Täpsustamise mõttes

Postitatud: 30.05.2006, 16:20
Postitas fiatimees
Suur mure mul. Rohelisena lasin ka oma masinale selle 6.06-e ja nüüd esialgu märganud kahte probleemi. Nimelt puudub igasugune heli. Vajutades heli reguleerijat leitakse viga GStreameriga??? Teiseks on kadunud võrgukaartide nimekirjast wifi kaart (eth1)???
Kas vaja drivereid või miskit muud??? Aidake hädalist.
tänud ette!
Postitatud: 30.05.2006, 16:42
Postitas jrepan
Mida näitab käsk "sudo ifconfig -a"
Postitatud: 30.05.2006, 17:05
Postitas fiatimees
Selline sedel ilmub:
gunnar@Workgroup:~$ sudo ifconfig -a
Password:
eth0 kapseldus:Ethernet HWaddr 00:0F:B0:81:DD:66
inet aadress:192.168.0.3 bcast:192.168.0.255 mask:255.255.255.0
inet6 aadr: fe80::20f:b0ff:fe81:dd66/64 skoop:ühendus
UP BROADCAST RUNNING MULTICAST MTU:1500 meetrika:1
RX pakette:44286 vigu:0 ära visatud:0 ületäit:0 kaadri vigu:0
TX pakette:33690 vigu:0 ära visatud:0 ületäit:0 carrier:0
kollisioone:0 txqueuelen:1000
RX baite:50693505 (48.3 MiB) TX baite:5589430 (5.3 MiB)
katkestus:21 baasaadress:0xc000
lo kapseldus:Kohalik loopback
inet aadress:127.0.0.1 mask:255.0.0.0
inet6 aadr: ::1/128 skoop:host
UP LOOPBACK RUNNING MTU:16436 meetrika:1
RX pakette:190751 vigu:0 ära visatud:0 ületäit:0 kaadri vigu:0
TX pakette:190751 vigu:0 ära visatud:0 ületäit:0 carrier:0
kollisioone:0 txqueuelen:0
RX baite:69342902 (66.1 MiB) TX baite:69342902 (66.1 MiB)
sit0 kapseldus:IPv6-in-IPv4
NOARP MTU:1480 meetrika:1
RX pakette:0 vigu:0 ära visatud:0 ületäit:0 kaadri vigu:0
TX pakette:0 vigu:0 ära visatud:0 ületäit:0 carrier:0
kollisioone:0 txqueuelen:0
RX baite:0 (0.0 b) TX baite:0 (0.0 b)
gunnar@Workgroup:~$
Postitatud: 30.05.2006, 17:34
Postitas imre
Mis wifi kaart sul üldse on ?
Kas vajalik tuuma moodul on laetud üldse ?
Saad vaadata käsuga sudo lsmod
Näita seda meilegi, koos wifi kaardi andmetega.
Ka "sudo dmesg" väljundi võiksid anda.
Lisa attachmendina need andmed.
Postitatud: 31.05.2006, 08:30
Postitas fiatimees
Niisiis selline:
Kood: Vali kõik
Module Size Used by
rfcomm 34972 0
l2cap 22404 5 rfcomm
bluetooth 43012 4 rfcomm,l2cap
snd 48644 0
soundcore 9184 1 snd
autofs4 16772 0
agpgart 32328 0
ppdev 9092 0
acpi_cpufreq 6020 1
cpufreq_userspace 4444 1
cpufreq_stats 5124 0
freq_table 4484 2 acpi_cpufreq,cpufreq_stats
cpufreq_powersave 1920 0
cpufreq_ondemand 5916 0
cpufreq_conservative 6820 0
video 16004 0
tc1100_wmi 6916 0
sony_acpi 5516 0
pcc_acpi 11392 0
hotkey 9508 0
dev_acpi 11396 0
i2c_acpi_ec 5760 0
i2c_core 19728 1 i2c_acpi_ec
button 6672 0
battery 9604 0
container 4608 0
ac 4996 0
rtc 11832 0
pcmcia 24584 2
yenta_socket 22540 1
rsrc_nonstatic 12032 1 yenta_socket
pcmcia_core 44932 3 pcmcia,yenta_socket,rsrc_nonstatic
ipv6 217408 14
dm_mod 50364 1
md 40656 0
sr_mod 15652 0
sbp2 21128 0
scsi_mod 124872 2 sr_mod,sbp2
ieee1394 90936 1 sbp2
psmouse 26116 0
mousedev 10912 1
parport_pc 31812 1
lp 11460 0
parport 32072 3 ppdev,parport_pc,lp
ext3 115976 1
jbd 48536 1 ext3
thermal 13192 0
processor 23100 2 acpi_cpufreq,thermal
fan 4740 0
usbhid 30688 0
8139too 23552 0
8139cp 18432 0
mii 5248 2 8139too,8139cp
ehci_hcd 29448 0
uhci_hcd 28048 0
usbcore 104316 4 usbhid,ehci_hcd,uhci_hcd
ide_cd 36996 0
cdrom 33952 2 sr_mod,ide_cd
ide_disk 16128 3
ide_generic 1664 0
piix 9476 1
ide_core 125268 4 ide_cd,ide_disk,ide_generic,piix
unix 24624 1063
vesafb 8088 0
capability 5000 0
commoncap 6784 1 capability
vga16fb 12232 1
vgastate 8320 1 vga16fb
softcursor 2432 2 vesafb,vga16fb
cfbimgblt 2944 2 vesafb,vga16fb
cfbfillrect 3840 2 vesafb,vga16fb
cfbcopyarea 4480 2 vesafb,vga16fb
fbcon 34176 72
tileblit 2560 1 fbcon
font 8448 1 fbcon
bitblit 5248 1 fbcon
Postitatud: 31.05.2006, 08:37
Postitas fiatimees
Seep siis järgmine.
Kood: Vali kõik
gunnar@Workgroup:~$ sudo dmesg
s)
[4294668.320000] Memory: 503172k/515964k available (1416k kernel code, 12288k reserved, 762k data, 224k init, 0k highmem)
[4294668.320000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[4294668.320000] Calibrating delay loop... 3416.06 BogoMIPS (lpj=1708032)
[4294668.344000] Security Framework v1.0.0 initialized
[4294668.344000] SELinux: Disabled at boot.
[4294668.344000] Mount-cache hash table entries: 512
[4294668.344000] CPU: After generic identify, caps: afe9fbff 00000000 00000000 00000000 00000180 00000000 00000000
[4294668.344000] CPU: After vendor identify, caps: afe9fbff 00000000 00000000 00000000 00000180 00000000 00000000
[4294668.344000] CPU: L1 I cache: 32K, L1 D cache: 32K
[4294668.344000] CPU: L2 cache: 2048K
[4294668.344000] CPU: After all inits, caps: afe9fbff 00000000 00000000 00000040 00000180 00000000 00000000
[4294668.344000] CPU: Intel(R) Pentium(R) M processor 1.73GHz stepping 08
[4294668.344000] Enabling fast FPU save and restore... done.
[4294668.344000] Enabling unmasked SIMD FPU exception support... done.
[4294668.344000] Checking 'hlt' instruction... OK.
[4294668.348000] Checking for popad bug... OK.
[4294668.348000] checking if image is initramfs... it is
[4294668.863000] Freeing initrd memory: 5165k freed
[4294668.863000] ACPI: Looking for DSDT in initrd... not found!
[4294668.907000] not found!
[4294669.003000] ENABLING IO-APIC IRQs
[4294669.003000] ..TIMER: vector=0x31 pin1=2 pin2=-1
[4294669.033000] NET: Registered protocol family 16
[4294669.033000] EISA bus registered
[4294669.033000] ACPI: bus type pci registered
[4294669.033000] PCI: PCI BIOS revision 2.10 entry at 0xea704, last bus=1
[4294669.033000] PCI: Using configuration type 1
[4294669.033000] mtrr: v2.0 (20020519)
[4294669.034000] ACPI: Subsystem revision 20050729
[4294669.056000] ACPI: Interpreter enabled
[4294669.056000] ACPI: Using IOAPIC for interrupt routing
[4294669.057000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[4294669.057000] PCI: Probing PCI hardware (bus 00)
[4294669.057000] ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
[4294669.078000] Boot video device is 0000:00:02.0
[4294669.079000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
[4294669.079000] PCI: Transparent bridge - 0000:00:1e.0
[4294669.086000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[4294669.087000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[4294669.087000] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[4294669.088000] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 11 12 14 15)[4294669.088000] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[4294669.088000] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)[4294669.088000] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)[4294669.088000] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)[4294669.089000] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[4294669.089000] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)[4294669.089000] burst-mode-ec-10-Aug
[4294669.089000] ACPI: Embedded Controller [EC0] (gpe 29)
[4294669.143000] Linux Plug and Play Support v0.97 (c) Adam Belay
[4294669.143000] pnp: PnP ACPI init
[4294669.170000] pnp: PnP ACPI: found 9 devices
[4294669.170000] PnPBIOS: Disabled by ACPI PNP
[4294669.170000] PCI: Using ACPI for IRQ routing
[4294669.170000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[4294669.174000] pnp: 00:02: ioport range 0x800-0x80f has been reserved
[4294669.174000] pnp: 00:02: ioport range 0x1000-0x107f could not be reserved
[4294669.175000] audit: initializing netlink socket (disabled)
[4294669.175000] audit: initialized
[4294669.175000] VFS: Disk quotas dquot_6.5.1
[4294669.175000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[4294669.175000] devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
[4294669.175000] devfs: boot_options: 0x0
[4294669.175000] Initializing Cryptographic API
[4294669.175000] isapnp: Scanning for PnP cards...
[4294669.529000] isapnp: No Plug & Play device found
[4294669.544000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[4294669.576000] i8042.c: Detected active multiplexing controller, rev 1.1.
[4294669.605000] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[4294669.610000] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[4294669.614000] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[4294669.619000] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[4294669.623000] serio: i8042 KBD port at 0x60,0x64 irq 1
[4294669.623000] Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
[4294669.625000] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 20 (level, low) -> IRQ 20
[4294669.625000] ACPI: PCI interrupt for device 0000:00:1e.3 disabled
[4294669.625000] io scheduler noop registered
[4294669.625000] io scheduler anticipatory registered
[4294669.625000] io scheduler deadline registered
[4294669.625000] io scheduler cfq registered
[4294669.625000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[4294669.632000] EISA: Probing bus 0 at eisa.0
[4294669.632000] Cannot allocate resource for EISA slot 1
[4294669.632000] EISA: Detected 0 cards.
[4294669.632000] NET: Registered protocol family 2
[4294669.654000] IP: routing cache hash table of 4096 buckets, 32Kbytes
[4294669.654000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[4294669.654000] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[4294669.654000] TCP: Hash tables configured (established 16384 bind 16384)
[4294669.654000] NET: Registered protocol family 8
[4294669.654000] NET: Registered protocol family 20
[4294669.654000] ACPI wakeup devices:
[4294669.654000] LANC MODM
[4294669.654000] ACPI: (supports S0 S3 S4 S5)
[4294669.655000] Freeing unused kernel memory: 224k freed
[4294669.692000] vga16fb: initializing
[4294669.692000] vga16fb: mapped to 0xc00a0000
[4294669.820000] Console: switching to colour frame buffer device 80x30
[4294669.820000] fb0: VGA16 VGA frame buffer device
[4294669.855000] input: AT Translated Set 2 keyboard on isa0060/serio0
[4294670.924000] Capability LSM initialized
[4294670.932000] NET: Registered protocol family 1
[4294670.944000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[4294670.944000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[4294670.944000] ACPI: bus type ide registered
[4294670.948000] ICH6: IDE controller at PCI slot 0000:00:1f.1
[4294670.948000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[4294670.948000] ICH6: chipset revision 4
[4294670.948000] ICH6: not 100% native mode: will probe irqs later
[4294670.948000] ide0: BM-DMA at 0x1100-0x1107, BIOS settings: hda:DMA, hdb:DMA
[4294670.948000] ide1: BM-DMA at 0x1108-0x110f, BIOS settings: hdc:pio, hdd:pio
[4294670.948000] Probing IDE interface ide0...
[4294671.212000] hda: TOSHIBA MK6034GAX, ATA DISK drive
[4294671.620000] hdb: _NEC DVD+/-RW ND-6650A, ATAPI CD/DVD-ROM drive
[4294671.671000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[4294671.671000] Probing IDE interface ide1...
[4294672.190000] Probing IDE interface ide1...
[4294672.708000] Probing IDE interface ide2...
[4294673.220000] Probing IDE interface ide3...
[4294673.732000] Probing IDE interface ide4...
[4294674.244000] Probing IDE interface ide5...
[4294674.758000] hda: max request size: 1024KiB
[4294674.781000] hda: 117210240 sectors (60011 MB), CHS=16383/255/63, UDMA(100)
[4294674.782000] hda: cache flushes supported
[4294674.782000] /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
[4294674.822000] hdb: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
[4294674.822000] Uniform CD-ROM driver Revision: 3.20
[4294674.994000] Attempting manual resume
[4294674.997000] swsusp: Suspend partition has wrong signature?
[4294675.026000] usbcore: registered new driver usbfs
[4294675.026000] usbcore: registered new driver hub
[4294675.026000] USB Universal Host Controller Interface driver v2.2
[4294675.026000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[4294675.026000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[4294675.026000] uhci_hcd 0000:00:1d.0: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1
[4294675.088000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[4294675.088000] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001200
[4294675.088000] hub 1-0:1.0: USB hub found
[4294675.088000] hub 1-0:1.0: 2 ports detected
[4294675.091000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[4294675.091000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[4294675.091000] uhci_hcd 0000:00:1d.1: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2
[4294675.153000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[4294675.153000] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001220
[4294675.153000] hub 2-0:1.0: USB hub found
[4294675.153000] hub 2-0:1.0: 2 ports detected
[4294675.156000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[4294675.156000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[4294675.156000] uhci_hcd 0000:00:1d.2: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3
[4294675.218000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[4294675.218000] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001240
[4294675.218000] hub 3-0:1.0: USB hub found
[4294675.218000] hub 3-0:1.0: 2 ports detected
[4294675.221000] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
[4294675.221000] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[4294675.221000] uhci_hcd 0000:00:1d.3: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4
[4294675.257000] usb 1-1: new low speed USB device using uhci_hcd and address 2
[4294675.283000] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[4294675.283000] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001260
[4294675.283000] hub 4-0:1.0: USB hub found
[4294675.283000] hub 4-0:1.0: 2 ports detected
[4294675.313000] PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
[4294675.313000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[4294675.313000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[4294675.313000] ehci_hcd 0000:00:1d.7: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller
[4294675.313000] ehci_hcd 0000:00:1d.7: debug port 1
[4294675.313000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[4294675.313000] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x1f800000
[4294675.317000] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[4294675.317000] ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
[4294675.317000] hub 5-0:1.0: USB hub found
[4294675.317000] hub 5-0:1.0: 8 ports detected
[4294675.391000] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[4294675.391000] 8139cp: pci dev 0000:01:01.0 (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[4294675.391000] 8139cp: Try the "8139too" driver instead.
[4294675.392000] 8139too Fast Ethernet driver 0.9.27
[4294675.392000] ACPI: PCI Interrupt 0000:01:01.0[A] -> GSI 21 (level, low) -> IRQ 21
[4294675.393000] eth0: RealTek RTL8139 at 0xc000, 00:0f:b0:81:dd:66, IRQ 21
[4294675.393000] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[4294675.897000] usb 1-1: new low speed USB device using uhci_hcd and address 3
[4294676.184000] usb 3-1: new low speed USB device using uhci_hcd and address 2
[4294677.434000] usbcore: registered new driver hiddev
[4294677.456000] input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-1
[4294677.475000] input: USB HID v1.10 Keyboard [CHICONY HP Basic USB Keyboard] on usb-0000:00:1d.2-1
[4294677.475000] usbcore: registered new driver usbhid
[4294677.475000] drivers/usb/input/hid-core.c: v2.01:USB HID core driver
[4294677.757000] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
[4294677.757000] ACPI: Processor [CPU0] (supports 8 throttling states)
[4294677.885000] Attempting manual resume
[4294677.886000] swsusp: Suspend partition has wrong signature?
[4294677.918000] kjournald starting. Commit interval 5 seconds
[4294677.918000] EXT3-fs: mounted filesystem with ordered data mode.
[4294687.537000] parport 0x378 (WARNING): CTR: wrote 0x0c, read 0xff
[4294687.537000] parport 0x378 (WARNING): DATA: wrote 0xaa, read 0xff
[4294687.537000] parport 0x378: You gave this address, but there is probably no parallel port there!
[4294687.537000] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[4294687.619000] lp0: using parport0 (interrupt-driven).
[4294687.792000] mice: PS/2 mouse device common for all mice
[4294688.306000] ieee1394: Initialized config rom entry `ip1394'
[4294688.407000] SCSI subsystem initialized
[4294688.578000] sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
[4294688.759000] Adding 1485972k swap on /dev/hda5. Priority:-1 extents:1
[4294688.811000] EXT3 FS on hda1, internal journal
[4294688.987000] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[4294689.060000] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x256eb1, caps: 0x804713/0x0
[4294689.060000] input: SynPS/2 Synaptics TouchPad on isa0060/serio4
[4294689.606000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[4294690.684000] cdrom: open failed.
[4294691.126000] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[4294691.537000] NET: Registered protocol family 10
[4294691.537000] Disabled Privacy Extensions on device c02eb280(lo)
[4294691.537000] IPv6 over IPv4 tunneling driver
[4294692.539000] Linux Kernel Card Services
[4294692.539000] options: [pci] [cardbus] [pm]
[4294692.543000] ACPI: PCI Interrupt 0000:01:04.0[A] -> GSI 16 (level, low) -> IRQ 16
[4294692.543000] Yenta: CardBus bridge found at 0000:01:04.0 [14c0:0012]
[4294692.663000] Yenta: ISA IRQ mask 0x0818, PCI irq 16
[4294692.663000] Socket status: 30000006
[4294693.079000] cs: IO port probe 0x100-0x4ff: excluding 0x170-0x177 0x230-0x237 0x370-0x37f 0x4d0-0x4d7
[4294693.081000] cs: IO port probe 0xc00-0xcf7: clean.
[4294693.082000] cs: IO port probe 0xa00-0xaff: clean.
[4294693.306000] Real Time Clock Driver v1.12
[4294693.363000] Generic RTC Driver v1.07
[4294693.950000] ACPI: AC Adapter [ACAD] (on-line)
[4294694.170000] ACPI: Battery Slot [BAT1] (battery present)
[4294694.193000] ACPI: Power Button (FF) [PWRF]
[4294694.193000] ACPI: Lid Switch [LID0]
[4294694.193000] ACPI: Power Button (CM) [PWRB]
[4294694.446000] ibm_acpi: ec object not found
[4294694.517000] ACPI: Video Device [GFX1] (multi-head: yes rom: no post: no)
[4294694.517000] ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no)[4294694.912000] acpi-cpufreq: CPU0 - ACPI performance management activated.
[4294699.271000] ppdev: user-space parallel port driver
[4294699.800000] Linux agpgart interface v0.101 (c) Dave Jones
[4294701.987000] eth0: no IPv6 routers present
[4294703.227000] apm: BIOS not found.
[4294711.811000] Bluetooth: Core ver 2.7
[4294711.811000] NET: Registered protocol family 31
[4294711.811000] Bluetooth: HCI device and connection manager initialized
[4294711.811000] Bluetooth: HCI socket layer initialized
[4294711.830000] Bluetooth: L2CAP ver 2.7
[4294711.830000] Bluetooth: L2CAP socket layer initialized
[4294711.926000] Bluetooth: RFCOMM ver 1.5
[4294711.926000] Bluetooth: RFCOMM socket layer initialized
[4294711.926000] Bluetooth: RFCOMM TTY layer initialized
gunnar@Workgroup:~$
Ette tänades ja abi lootes!
Postitatud: 01.06.2006, 10:41
Postitas fiatimees
Appi!?
Pole veel lahendust leidnud!?:-(
Postitatud: 01.06.2006, 11:12
Postitas vih
Alustame kõige pealt hiirest ehk? Ma ju küsisin sinu Xi logi, kui sul see tööle ei läinud. Vastust pole.
Teiseks, mis helikaart sul on? Vastavad baasmoodulid paistavad olevat tuumas olemas, kuid mingit spetsiifilist helidraiverit mina ei näe.
Ehk siis, sinu kaks viimast probleemi peaksid saama ajutiselt (pheks boodiks) lahendatud kui sa modprobe käsuga laed oma helikaardi ja wifikaardi draiverid. Seda saab hõlpsasi teha kui sul on mõni LiveCD või mu NIX süsteem, mis tunneb ära need kaardid. Sealt saaksid omale õigete draiverite nimed. Neid saab ka kuskil netist muidu, kui sul kaardide õiged nimetused olemas on.
Postitatud: 01.06.2006, 14:21
Postitas digweed
Vampire,x logi küsisid minu käest

ubuntu maha lastud.täna proovin ehk uuesti

dapper vist ametlikult väljas al.tänasest
Postitatud: 01.06.2006, 14:32
Postitas vih
8-O
Vabandan. See on hijackimise viga

Postitatud: 01.06.2006, 14:40
Postitas fiatimees
No juba sattusin segadusse - roheline ju ja tõmbasin veel rohelisemaks. Tunnistan oma probleeme, sest winni pealt tulnud tavakasutajal on ülemineku probleemid. Seega vajaks abi heli taasesitluseks ja wifi tööle rakendamiseks.
g.
Postitatud: 01.06.2006, 14:41
Postitas digweed
esmalt toksi teriminali alsamixer ja lükka kõik põhja.
Postitatud: 01.06.2006, 14:55
Postitas fiatimees
Niisiis sain järgmise veateate
alsamixer: function snd_ctl_open failed for default: No such device

Postitatud: 01.06.2006, 16:46
Postitas imre
Just kaklesin Ubuntu all samasuguse murega.
Mind aitas see link:
http://isiklik.info/ubuntuguide/#configuresoundproperly
Tee ära, logi välja sisse tagasi.
Tööle hakkas.
Kuidas, sellest ma ei saanudki aru.
Imelik, et ta kohe ei võtnud omaks uuendust.
Postitatud: 01.06.2006, 16:48
Postitas digweed
Innu kirjutas:Section "InputDevice"
Identifier "Configured Mouse"
Driver "evdev"
Option "CorePointer"
Option "Device" "/dev/input/event1"
Option "Dev Name" "Logitech USB-PS/2 Optical Mouse"
Option "Resolution" "800"
Option "Buttons" "10"
Option "ZAxisMapping" "9 10"
Option "Dev Phys" "usb-*/input0"
EndSection
Mx518 ja nii toimib hiir mul täielikult.
dapper peal ja minu mx700 sobib täpselt sama tekst (y)
siit kohe uus küsimus.
bootides laeb mul tv/fm kaardi väheke valesti ära.
ja vaja teha alati peale igat restarti selline liigutus:
rmmod saa7134_alsa
rmmod saa7134
ehk siis laeb valed moodulid.
tööle läheb nii:modprobe saa7134 card=3 tuner=1.kuhu ma muudatuse sisse pean viima?
Postitatud: 01.06.2006, 17:23
Postitas vih
Ma pakun et /etc/rc.conf.