Pingviini veeb

Postitatud: **13.12.2009, 02:02**

Tere jälle hea foorumi rahvas. Mul probleem välise kõvakakaga. Arvan, et see polegi niivõrd Linuxi, kui lihtsalt ketta enda probleem, aga kui siin juba olen, küsin siit nõu. Asi siis järgmine: varem ketas töötas ( WD Passport 160 GB) ilma igasuguste probleebidetta. Nüüd millegipärast ei taha käima minna. Ma ei saa täpselt aru, milles viga, aga tundub asi hakkas pihta peale seda kui ma järjekordselt olin ta vindoosa masinasse ühendanud ( et filmi hDragonist tümmata, linuxis hDragon ei tööta), olin ka varem seda teinud ja probleeme pole olnud, aga miongil ajal hakkas selline jama, et enam ei ketas ei avanenud minu linuxiga masinas, ja vindoosa masinas samuti. Vindoosas kirjutab, et ( ega minu inglise arusaamine pole just suurem asi aga vist umbes nii ) on leitud uus raudvara aga devaiss ründab ja Windows ei saa seda avada. Linuxis ei kirjuta midagi, lihtsalt ketas ei avane. Muidugi on see ketas mul põrutada ja raputada saanud, aga mis kõige imelikum- aeg.ajalt ikkagi käima saab. Mingil ajal avastasin , et kui liigutasin ketta ja läpaka vahelist USB kaablit, ketas kadus, ketast ei liigutanud. mudisin jälle kaablit- ketas tuli tagasi. Töö juures proovisin ühe fotoka sobilke otstega kaabliga- ja hopa asi töötas nagu siili, igaks juhuks kontrolli mõttes ühendasin lahti ja jälle tagasi . Ilusasti võttis jälle ketta külge, mingit problemit. Mõtlesin, et asi kaablis ( kass närinud, või miskit, aga hambajälgi pole)) ostsin uue kaabli, anti mingi ilgelt pikk juhe, sellega ketas ainult tiksuma jäigi. Pärast vana originaalkaabliga ja peale mitmekordseid sisse-välja ühendamisi ja ketta raputamisi ja koputamisi ketas ikkagi tööle hakkab. Ja naljakas on veel see, et tundub nagu asi kellaajast sõltuks- ennem kella 11 öösel ketast külge ei saa!
Mitte ei saa aru, milles siis asi tegelikult on?
Kas võib abi olla ketta puhastamisest-tühjendamisest.? 160 GB ne ketas, vaba ruumi veel 50 GB.
Naljakas ja pikk jutt sai vist, aga tõesti ei saa aru milles asi. Vaja uus ketas osta?

Edit: ja imelik on veel see , et varem, kui asi töötas probleemidetta, viskas ühendmisel desktopile ikooni - folder 160 GB media- või midagi sellist, aga nüüd kui õnnestub ühendada näitab ainult Placese all ketta olemasolu.

Postitatud: **13.12.2009, 02:45**

Tiksumine viitab tõsisele riistvaraveale, lugemispea ei suuda end korralikult positsioneerida. Igaks juhuks võid ketta taha ühendada ja vaadata, mida siis käsk "sudo fdisk -l" ütleb.

Postitatud: **13.12.2009, 03:37**

Sihukest asja ütles. Ma ei oska sellest miskit välja lugeda.

Disk /dev/sda: 4001 MB, 4001292288 bytes
255 heads, 63 sectors/track, 486 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x332b332a

Device Boot Start End Blocks Id System
/dev/sda1 * 1 458 3678853+ 83 Linux
/dev/sda2 459 486 224910 5 Extended
/dev/sda5 459 486 224878+ 82 Linux swap / Solaris

Disk /dev/sdc: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x5b6ac646

Device Boot Start End Blocks Id System
/dev/sdc1 1 19457 156288321 c W95 FAT32 (LBA)
jaanus@jaanus:~

vist ikka ketas ise on nässus. Kui se jama hakkas, et enam ei haakinud külge, siis ma ju teda ika päris kõvsti raputasin ja koputanud olen ja isegi natuke tahtlikult kukutanud nii erinevate nurkade peale ca 50 cm. kõrguselt. No ei teadnud enam, mida teha et ********** tööle hakkaks

Postitatud: **13.12.2009, 03:50**

Edit: A praegu on taga ja töötab. Isegi imestan, et peale kõiki neid loomkatseid ikka veel tötab!

Postitatud: **13.12.2009, 04:54**

/dev/sdc1 1 19457 156288321 c W95 FAT32 (LBA)

See näitab, et hetkel on ta initsialiseeritud ja valmis kasutamiseks. Nii et kui ketta peal midagi olulist on, siis kiiresti koopia ja seejärel juba kettale diagnostka peale. Kukutamised on muidugi piisav "diagnostika", et ketast enam mitte usaldada.

Postitatud: **13.12.2009, 17:01**

ja ketta raputamisi ja koputamisi ketas ikkagi tööle hakkab

ma ei saa aru mida sa sellest ketast tahad kui sa seda peksad ja toksid ja neid juhtmeid mudid
Kui sa saadad invaliidist sõduri sõtta, kelle ei ole ühte jalga ja kätt, ning eeldad et ta käituks nagu arnold???

Ketas on persses ja jutul lõpp, viska metsa oma pekstud ja tambitud ketas ära kasuta seda enam jääd oma viimastest andmetest ilma

Ma ei saa aru, kust inimesed võtavad et põrutatud/raputatud/loobitud ketas peaks toimima perfektselt... Kettad kui sellised on väga õrnad asjad jäta see omale meelde kui järgmine kord sellise jutuga lagedale tuled!

Postitatud: **13.12.2009, 18:53**

no mis te nüüd riidlete niimoodi! ma olin ju täitsa endast välja viidud- tahtsin filmi vaadata, aga ei saanud, ja peale neid raputamisi ja koputamisi ta ju hakkas tööle. Aga see selleks, ega poleks tohtinud jah niimoodi teha. Nüüd olen targem. Ütleme, et viskasingi metsa selle minema. Ostsin täna uue ketta 320 GB. ostsin eraldi ketta ja selle nn. case, koos selle kiibi ja plaadikesega. noh poes formaaditi ära, proovisime nii minu vana skeemiga ja minu juhtmetega ja igasuguseid eri variante, lõpuks jäi mulje, et asi ainult oma originaal juhtme ja skeemiga tööle hakkas, kusjuures juhtmel oli 2 USB otsa ja mõlemad pidid sisse pistetud olema, siis hakkas tööle. Müüa arvas, et toidet jääb ühega väheseks. On see normaalne? Mul oli juba kõrini seal passimisest (oodata kuni formaaditi) ja proovimisest ja kogu sellest jamast ja ostsingi mõlemad ära, nii ketta kui selle case koos skeemijupikesega. Müüja küsis, et kas on vaja karbi sisse panna, või ehk võtan niisama, pistan kohe taskusse, ma tahtsin ikka karbiga saada, aga siis tal tuli midagi vahele ja mul oli kah pea laiali otsas ja nii ma võtsingi selle ilma karbita ja juhet ei märganud kah kaaa võtta. Nüüd kodus oma vanade juhtmetega proovides asi ikkagi käima ei lähe! Vaja homme juhet nõudma minna, või annan selle krempeli neile tagasi ja ostan ikka juba valmis komplektse ketta.

Postitatud: **14.12.2009, 09:07**

samsungime kirjutas:ma ju teda ika päris kõvsti raputasin ja koputanud olen ja isegi natuke tahtlikult kukutanud nii erinevate nurkade peale ca 50 cm. kõrguselt.

Kõvaketta magnetraja laius on umbes 200-250 nm. Nähtava valguse lainepikkus on 2-3 korda suurem. Nii täpselt on vaja lugemispäid positsioneerida, nii et ei maksa pahandada, kui ka pärast viie cm kõrguselt kukutamist lugemisega hakkama ei saa. Kui mina poemüüja oleks, ei võtaks ma ilma karbita taskus kantud ketast enam tagasi.

Postitatud: **14.12.2009, 10:30**

samsungime kirjutas:lõpuks jäi mulje, et asi ainult oma originaal juhtme ja skeemiga tööle hakkas, kusjuures juhtmel oli 2 USB otsa ja mõlemad pidid sisse pistetud olema, siis hakkas tööle. Müüa arvas, et toidet jääb ühega väheseks.

Siis jääb suht kindlalt toidet väheks. Kõige rohkem on vaja toidet siis, kui ketas ennast käima tõmbab.

Postitatud: **14.12.2009, 12:11**

pika kaabli vahele toppimisel pigem ka asi selles, et toide polnud piisav.. ega neid otsi seal naljalt kaks pole..

diagnostika jaoks on smartmontools ja graafiliseks väljundiks sellele gsmartcontrol - sellega peaksid saama vaadata, kas kettal on esinenud vigu toimimises.. muidugi kõigepealt anna kettale piisavalt toidet, tühja akuga autot ju ei käivita, miks peaks pooletoobine toide ketast ringi ajama?

Postitatud: **14.12.2009, 17:34**

Ok. jälle natuke targem. Aga sain täna oma juhtme ja ülejäänud asjad kah sealt poest ikka kätte. Hakkasin algul küll pakkuma, et ehk võtavad tagasi ja ostan sealt ühe valmis ketta- jäi silma sellises pehmemas korpuses ja peal kirjutas kah et mingid US Army põrutustestid läbind jne. Aga müüa kiitis ka seda olemasolevat varianti, mis eile ostsin, väga heaks ja poes tema õige juhtmega veelkord proovides läks nüüd asi ka ühe otsaga käima ja kõik tundub OK. olevat. Luban, et edaspidi püüan selle kettaga väga õrnalt ringi käia!

Postitatud: **14.12.2009, 19:21**

Lisainfoks veel seda, et kui USB hosti kontroller ei suuda piisavat toidet tagada, siis peaks kernel oma logisse ka vastava teate saatma.

Ei suutnud küll riistvara puudumisel sinu juhtumit täpselt korrata, ent siiski siin on üks näide, milles toiteprobleemidest teavitatakse.
Antud juhtumil ei suuda (ei taha?) Apple USB klaviatuur tagada piisavat toidet USB 2.0 mälupulgale, mille tulemusel ilmub kerneli logisse selline jutt:

Kood: Vali kõik

mac:~$ dmesg 
[  220.402053] usb 2-1.2: new full speed USB device using uhci_hcd and address 4
[  220.503049] usb 2-1.2: not running at top speed; connect to a high speed hub
[  220.526052] usb 2-1.2: New USB device found, idVendor=0ea0, idProduct=2168
[  220.526058] usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  220.526064] usb 2-1.2: Product: Flash Disk
[  220.526068] usb 2-1.2: Manufacturer: USB
[  220.526072] usb 2-1.2: SerialNumber: B8D1423F696B00D8
[  220.526220] usb 2-1.2: rejected 1 configuration due to insufficient available bus power
[  220.526226] usb 2-1.2: no configuration chosen from 1 choice
mac:~$

Oluline on eelviimane rida: rejected 1 configuration due to insufficient available bus power.

Postitatud: **14.12.2009, 23:52**

proovisin jälle oma vana ketast ühendada, ei saanud, nüüd uus ketas taga kerneli logi annab sellise jutu, ma nagu ikka suurt miskit aru ei saa

[ 4.656235] usb usb1: configuration #1 chosen from 1 choice
[ 4.656325] hub 1-0:1.0: USB hub found
[ 4.656347] hub 1-0:1.0: 8 ports detected
[ 4.656659] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.656709] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.656808] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 4.656827] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 4.656835] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 4.656994] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 4.657033] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e400
[ 4.657241] usb usb2: configuration #1 chosen from 1 choice
[ 4.657313] hub 2-0:1.0: USB hub found
[ 4.657333] hub 2-0:1.0: 2 ports detected
[ 4.657558] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 4.657573] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 4.657581] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 4.657697] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 4.657756] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e480
[ 4.657952] usb usb3: configuration #1 chosen from 1 choice
[ 4.658023] hub 3-0:1.0: USB hub found
[ 4.658041] hub 3-0:1.0: 2 ports detected
[ 4.658262] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 4.658276] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 4.658284] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 4.658406] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 4.658458] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800
[ 4.658667] usb usb4: configuration #1 chosen from 1 choice
[ 4.658738] hub 4-0:1.0: USB hub found
[ 4.658757] hub 4-0:1.0: 2 ports detected
[ 4.658979] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 4.658993] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 4.659001] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 4.659137] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 4.659188] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e880
[ 4.659414] usb usb5: configuration #1 chosen from 1 choice
[ 4.659490] hub 5-0:1.0: USB hub found
[ 4.659507] hub 5-0:1.0: 2 ports detected
[ 4.659946] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 4.691770] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 4.691786] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 4.692125] mice: PS/2 mouse device common for all mice
[ 4.692645] rtc_cmos 00:03: RTC can wake from S4
[ 4.692762] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 4.692804] rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
[ 4.693023] device-mapper: uevent: version 1.0.3
[ 4.693456] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 4.693605] device-mapper: multipath: version 1.0.5 loaded
[ 4.693614] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 4.693866] EISA: Probing bus 0 at eisa.0
[ 4.693920] EISA: Detected 0 cards.
[ 4.694127] cpuidle: using governor ladder
[ 4.694301] cpuidle: using governor menu
[ 4.695702] TCP cubic registered
[ 4.696001] NET: Registered protocol family 10
[ 4.697151] lo: Disabled Privacy Extensions
[ 4.698013] NET: Registered protocol family 17
[ 4.698073] Bluetooth: L2CAP ver 2.11
[ 4.698078] Bluetooth: L2CAP socket layer initialized
[ 4.698110] Bluetooth: SCO (Voice Link) ver 0.6
[ 4.698115] Bluetooth: SCO socket layer initialized
[ 4.698212] Bluetooth: RFCOMM socket layer initialized
[ 4.698239] Bluetooth: RFCOMM TTY layer initialized
[ 4.698244] Bluetooth: RFCOMM ver 1.10
[ 4.698361] Using IPI No-Shortcut mode
[ 4.698593] registered taskstats version 1
[ 4.698880] Magic number: 5:682:746
[ 4.699062] rtc_cmos 00:03: setting system clock to 2009-12-14 18:42:34 UTC (1260816154)
[ 4.699071] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 4.699077] EDD information not available.
[ 4.699753] Freeing unused kernel memory: 532k freed
[ 4.700223] Write protecting the kernel text: 4120k
[ 4.700340] Write protecting the kernel read-only data: 1524k
[ 4.736259] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 4.968550] usb 1-5: new high speed USB device using ehci_hcd and address 2
[ 5.101289] usb 1-5: configuration #1 chosen from 1 choice
[ 5.700959] Marking TSC unstable due to TSC halts in idle
[ 5.953376] Initializing USB Mass Storage driver...
[ 5.957546] scsi2 : SCSI emulation for USB Mass Storage devices
[ 5.959503] usbcore: registered new interface driver usb-storage
[ 5.959515] USB Mass Storage support registered.
[ 5.960001] usb-storage: device found at 2
[ 5.960095] usb-storage: waiting for device to settle before scanning
[ 6.735597] PM: Starting manual resume from disk
[ 6.735609] PM: Resume from partition 8:5
[ 6.735614] PM: Checking hibernation image.
[ 6.736136] PM: Resume from disk failed.
[ 6.745686] kjournald starting. Commit interval 5 seconds
[ 6.745716] EXT3-fs: mounted filesystem with ordered data mode.
[ 6.904045] Clocksource tsc unstable (delta = -130150169 ns)
[ 9.143968] udev: starting version 141
[ 9.310706] eeepc: Eee PC Hotkey Driver
[ 9.407813] eeepc: Hotkey init flags 0x41
[ 9.409122] eeepc: Get control methods supported: 0x101711
[ 9.409451] input: Asus EeePC extra buttons as /devices/virtual/input/input6
[ 9.574338] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:16/input/input7
[ 9.604395] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 9.677224] Linux agpgart interface v0.103
[ 9.693276] agpgart-intel 0000:00:00.0: Intel 915GM Chipset
[ 9.693721] agpgart-intel 0000:00:00.0: detected 7932K stolen memory
[ 9.706879] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[ 9.822887] Atheros(R) L2 Ethernet Driver - version 2.2.3
[ 9.822897] Copyright (c) 2007 Atheros Corporation.
[ 9.822991] atl2 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 9.823013] atl2 0000:03:00.0: setting latency timer to 64
[ 9.920194] cfg80211: Calling CRDA to update world regulatory domain
[ 10.083899] ath5k_pci 0000:01:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 10.083922] ath5k_pci 0000:01:00.0: setting latency timer to 64
[ 10.084235] ath5k_pci 0000:01:00.0: registered as 'phy0'
[ 10.141226] phy0: Selected rate control algorithm 'pid'
[ 10.162235] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 10.162328] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 10.193930] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
[ 10.232881] intel_rng: FWH not detected
[ 10.253984] iTCO_vendor_support: vendor-support=0
[ 10.259649] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[ 10.260052] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x0860)
[ 10.260272] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 10.361301] input: PC Speaker as /devices/platform/pcspkr/input/input8
[ 10.529903] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[ 10.963818] usb-storage: device scan complete
[ 10.964591] scsi 2:0:0:0: Direct-Access USB2.0 CardReader SD0 0100 PQ: 0 ANSI: 0
[ 10.968546] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 10.968978] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 11.299166] cfg80211: World regulatory domain updated:
[ 11.299180] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 11.299189] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.299198] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 11.299205] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 11.299213] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.299221] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.736754] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x180b1, caps: 0xa04753/0x200000
[ 11.745259] lp: driver loaded but no devices found
[ 11.841472] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input9
[ 11.990849] Adding 224868k swap on /dev/sda5. Priority:-1 extents:1 across:224868k
[ 12.038021] EXT3 FS on sda1, internal journal
[ 12.764515] type=1505 audit(1260816162.564:2): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=1911
[ 12.764957] type=1505 audit(1260816162.564:3): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=1911
[ 12.765143] type=1505 audit(1260816162.564:4): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=1911
[ 12.765299] type=1505 audit(1260816162.564:5): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=1911
[ 13.230415] type=1505 audit(1260816163.028:6): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=1916
[ 13.231024] type=1505 audit(1260816163.028:7): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=1916
[ 13.321321] type=1505 audit(1260816163.120:8): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=1920
[ 16.721994] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 16.722003] Bluetooth: BNEP filters: protocol multicast
[ 16.755154] Bridge firewalling registered
[ 19.072747] ppdev: user-space parallel port driver
[ 20.718209] [drm] Initialized drm 1.1.0 20060810
[ 20.754999] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 20.755014] pci 0000:00:02.0: setting latency timer to 64
[ 20.755430] [drm] Initialized i915 1.6.0 20080730 on minor 0
[ 20.760931] [drm:i915_setparam] *ERROR* unknown parameter 4
[ 20.760994] [drm:i915_getparam] *ERROR* Unknown parameter 6
[ 22.200814] atl2 0000:03:00.0: irq 2300 for MSI/MSI-X
[ 22.201080] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 22.268323] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 22.706443] [drm:i915_getparam] *ERROR* Unknown parameter 6
[ 62.902258] wlan0: authenticate with AP 00:25:9c:23:fb:96
[ 62.903816] wlan0: authenticated
[ 62.903827] wlan0: associate with AP 00:25:9c:23:fb:96
[ 62.906174] wlan0: RX AssocResp from 00:25:9c:23:fb:96 (capab=0x411 status=0 aid=2)
[ 62.906184] wlan0: associated
[ 62.907110] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 73.516042] wlan0: no IPv6 routers present
[ 78.448133] usb 3-2: new full speed USB device using uhci_hcd and address 2
[ 78.591957] usb 3-2: not running at top speed; connect to a high speed hub
[ 78.622753] usb 3-2: configuration #1 chosen from 1 choice
[ 78.643416] scsi3 : SCSI emulation for USB Mass Storage devices
[ 78.661007] usb-storage: device found at 2
[ 78.661016] usb-storage: waiting for device to settle before scanning
[ 83.662065] usb-storage: device scan complete
[ 83.665083] scsi 3:0:0:0: Direct-Access WD 1600BEV External 1.04 PQ: 0 ANSI: 4
[ 83.719045] sd 3:0:0:0: [sdc] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
[ 83.724128] sd 3:0:0:0: [sdc] Write Protect is off
[ 83.724141] sd 3:0:0:0: [sdc] Mode Sense: 21 00 00 00
[ 83.724149] sd 3:0:0:0: [sdc] Assuming drive cache: write through
[ 83.729207] sd 3:0:0:0: [sdc] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
[ 83.734219] sd 3:0:0:0: [sdc] Write Protect is off
[ 83.734232] sd 3:0:0:0: [sdc] Mode Sense: 21 00 00 00
[ 83.734240] sd 3:0:0:0: [sdc] Assuming drive cache: write through
[ 83.734261] sdc: sdc1
[ 83.797091] sd 3:0:0:0: [sdc] Attached SCSI disk
[ 83.797291] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 145.820079] usb 3-2: reset full speed USB device using uhci_hcd and address 2
[ 145.940087] usb 3-2: device descriptor read/64, error -71
[ 146.164074] usb 3-2: device descriptor read/64, error -71
[ 146.380057] usb 3-2: reset full speed USB device using uhci_hcd and address 2
[ 146.516050] usb 3-2: device descriptor read/64, error -71
[ 146.765578] usb 3-2: device descriptor read/64, error -71
[ 146.980044] usb 3-2: reset full speed USB device using uhci_hcd and address 2
[ 147.388024] usb 3-2: device not accepting address 2, error -71
[ 147.500033] usb 3-2: reset full speed USB device using uhci_hcd and address 2
[ 147.908027] usb 3-2: device not accepting address 2, error -71
[ 147.908191] sd 3:0:0:0: [sdc] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[ 147.908205] end_request: I/O error, dev sdc, sector 0
[ 147.908216] Buffer I/O error on device sdc, logical block 0
[ 147.908232] Buffer I/O error on device sdc, logical block 1
[ 147.908240] Buffer I/O error on device sdc, logical block 2
[ 147.908248] Buffer I/O error on device sdc, logical block 3
[ 147.908373] usb 3-2: USB disconnect, address 2
[ 147.916097] sd 3:0:0:0: [sdc] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[ 147.916115] end_request: I/O error, dev sdc, sector 0
[ 147.916128] Buffer I/O error on device sdc, logical block 0
[ 148.063560] usb 3-2: new full speed USB device using uhci_hcd and address 3
[ 148.244049] usb 3-2: device descriptor read/64, error -71
[ 148.472107] usb 3-2: device descriptor read/64, error -71
[ 148.688029] usb 3-2: new full speed USB device using uhci_hcd and address 4
[ 148.808133] usb 3-2: device descriptor read/64, error -71
[ 149.036129] usb 3-2: device descriptor read/64, error -71
[ 149.252058] usb 3-2: new full speed USB device using uhci_hcd and address 5
[ 149.664125] usb 3-2: device not accepting address 5, error -71
[ 149.776126] usb 3-2: new full speed USB device using uhci_hcd and address 6
[ 150.192176] usb 3-2: device not accepting address 6, error -71
[ 150.192214] hub 3-0:1.0: unable to enumerate USB device on port 2
[ 200.576122] usb 1-4: new high speed USB device using ehci_hcd and address 4
[ 200.712401] usb 1-4: configuration #1 chosen from 1 choice
[ 200.722564] scsi4 : SCSI emulation for USB Mass Storage devices
[ 200.746216] usb-storage: device found at 4
[ 200.746224] usb-storage: waiting for device to settle before scanning
[ 205.744381] usb-storage: device scan complete
[ 205.745111] scsi 4:0:0:0: Direct-Access WD 1600BEV External 1.04 PQ: 0 ANSI: 4
[ 205.750075] sd 4:0:0:0: [sdc] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
[ 205.795465] sd 4:0:0:0: [sdc] Write Protect is off
[ 205.795478] sd 4:0:0:0: [sdc] Mode Sense: 21 00 00 00
[ 205.795486] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 205.797833] sd 4:0:0:0: [sdc] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
[ 205.798691] sd 4:0:0:0: [sdc] Write Protect is off
[ 205.798701] sd 4:0:0:0: [sdc] Mode Sense: 21 00 00 00
[ 205.798708] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 205.798727] sdc: sdc1
[ 205.855717] sd 4:0:0:0: [sdc] Attached SCSI disk
[ 205.855922] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 224.100052] usb 2-2: new full speed USB device using uhci_hcd and address 2
[ 224.224095] usb 2-2: device descriptor read/64, error -71
[ 224.508045] usb 2-2: device descriptor read/64, error -71
[ 224.724134] usb 2-2: new full speed USB device using uhci_hcd and address 3
[ 224.848112] usb 2-2: device descriptor read/64, error -71
[ 225.076133] usb 2-2: device descriptor read/64, error -71
[ 225.292047] usb 2-2: new full speed USB device using uhci_hcd and address 4
[ 225.704115] usb 2-2: device not accepting address 4, error -71
[ 225.816111] usb 2-2: new full speed USB device using uhci_hcd and address 5
[ 226.232096] usb 2-2: device not accepting address 5, error -71
[ 226.232142] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 338.257025] usb 1-4: USB disconnect, address 4
[ 338.260841] Buffer I/O error on device sdc1, logical block 48844988
[ 338.260854] lost page write due to I/O error on sdc1
[ 338.260875] Buffer I/O error on device sdc1, logical block 48844991
[ 338.260882] lost page write due to I/O error on sdc1
[ 338.260894] Buffer I/O error on device sdc1, logical block 48844992
[ 338.260901] lost page write due to I/O error on sdc1
[ 355.116135] usb 1-2: new high speed USB device using ehci_hcd and address 6
[ 355.297711] usb 1-2: configuration #1 chosen from 1 choice
[ 355.337522] scsi5 : SCSI emulation for USB Mass Storage devices
[ 355.337835] usb-storage: device found at 6
[ 355.337843] usb-storage: waiting for device to settle before scanning
[ 360.336399] usb-storage: device scan complete
[ 363.425414] scsi 5:0:0:0: Direct-Access General Hard Disk PQ: 0 ANSI: 2 CCS
[ 363.497394] sd 5:0:0:0: [sdc] Attached SCSI disk
[ 363.497585] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 371.596995] usb 1-2: USB disconnect, address 6
[ 406.508102] usb 1-3: new high speed USB device using ehci_hcd and address 7
[ 406.672010] usb 1-3: configuration #1 chosen from 1 choice
[ 406.709231] scsi6 : SCSI emulation for USB Mass Storage devices
[ 406.724877] usb-storage: device found at 7
[ 406.724887] usb-storage: waiting for device to settle before scanning
[ 411.724283] usb-storage: device scan complete
[ 411.795414] scsi 6:0:0:0: Direct-Access WDC WD32 00BEVT-11ZCT0 PQ: 0 ANSI: 2 CCS
[ 411.800381] sd 6:0:0:0: [sdc] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 411.847894] sd 6:0:0:0: [sdc] Write Protect is off
[ 411.847907] sd 6:0:0:0: [sdc] Mode Sense: 3c 00 00 00
[ 411.847915] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 411.850217] sd 6:0:0:0: [sdc] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 411.851726] sd 6:0:0:0: [sdc] Write Protect is off
[ 411.851738] sd 6:0:0:0: [sdc] Mode Sense: 3c 00 00 00
[ 411.851746] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 411.851764] sdc: sdc1
[ 411.896444] sd 6:0:0:0: [sdc] Attached SCSI disk
[ 411.896663] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 466.584075] usb 2-2: new full speed USB device using uhci_hcd and address 6
[ 466.708049] usb 2-2: device descriptor read/64, error -71
[ 466.936131] usb 2-2: device descriptor read/64, error -71
[ 467.152068] usb 2-2: new full speed USB device using uhci_hcd and address 7
[ 467.332125] usb 2-2: device descriptor read/64, error -71
[ 467.560142] usb 2-2: device descriptor read/64, error -71
[ 467.776047] usb 2-2: new full speed USB device using uhci_hcd and address 8
[ 468.188130] usb 2-2: device not accepting address 8, error -71
[ 468.300120] usb 2-2: new full speed USB device using uhci_hcd and address 9
[ 468.716049] usb 2-2: device not accepting address 9, error -71
[ 468.716094] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 489.140200] usb 2-2: new full speed USB device using uhci_hcd and address 10
[ 489.264051] usb 2-2: device descriptor read/64, error -71
[ 489.488162] usb 2-2: device descriptor read/64, error -71
[ 489.704066] usb 2-2: new full speed USB device using uhci_hcd and address 11
[ 489.828063] usb 2-2: device descriptor read/64, error -71
[ 490.052060] usb 2-2: device descriptor read/64, error -71
[ 490.268062] usb 2-2: new full speed USB device using uhci_hcd and address 12
[ 490.680054] usb 2-2: device not accepting address 12, error -71
[ 490.792050] usb 2-2: new full speed USB device using uhci_hcd and address 13
[ 491.204042] usb 2-2: device not accepting address 13, error -71
[ 491.204081] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 533.022152] usb 2-2: new full speed USB device using uhci_hcd and address 14
[ 533.144050] usb 2-2: device descriptor read/64, error -71
[ 533.368063] usb 2-2: device descriptor read/64, error -71
[ 533.584049] usb 2-2: new full speed USB device using uhci_hcd and address 15
[ 533.704081] usb 2-2: device descriptor read/64, error -71
[ 533.928045] usb 2-2: device descriptor read/64, error -71
[ 534.144043] usb 2-2: new full speed USB device using uhci_hcd and address 16
[ 534.552046] usb 2-2: device not accepting address 16, error -71
[ 534.664080] usb 2-2: new full speed USB device using uhci_hcd and address 17
[ 535.076045] usb 2-2: device not accepting address 17, error -71
[ 535.076078] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 594.434277] usb 1-3: USB disconnect, address 7
[ 605.380143] usb 3-1: new full speed USB device using uhci_hcd and address 7
[ 605.500056] usb 3-1: device descriptor read/64, error -71
[ 605.728223] usb 3-1: device descriptor read/64, error -71
[ 605.944171] usb 3-1: new full speed USB device using uhci_hcd and address 8
[ 606.068140] usb 3-1: device descriptor read/64, error -71
[ 606.296186] usb 3-1: device descriptor read/64, error -71
[ 606.512147] usb 3-1: new full speed USB device using uhci_hcd and address 9
[ 606.920154] usb 3-1: device not accepting address 9, error -71
[ 607.032145] usb 3-1: new full speed USB device using uhci_hcd and address 10
[ 607.440156] usb 3-1: device not accepting address 10, error -71
[ 607.440201] hub 3-0:1.0: unable to enumerate USB device on port 1
[ 627.344060] usb 3-1: new full speed USB device using uhci_hcd and address 11
[ 627.464082] usb 3-1: device descriptor read/64, error -71
[ 627.688062] usb 3-1: device descriptor read/64, error -71
[ 627.904058] usb 3-1: new full speed USB device using uhci_hcd and address 12
[ 628.024059] usb 3-1: device descriptor read/64, error -71
[ 628.248078] usb 3-1: device descriptor read/64, error -71
[ 628.464091] usb 3-1: new full speed USB device using uhci_hcd and address 13
[ 628.876157] usb 3-1: device not accepting address 13, error -71
[ 628.988063] usb 3-1: new full speed USB device using uhci_hcd and address 14
[ 629.396055] usb 3-1: device not accepting address 14, error -71
[ 629.396093] hub 3-0:1.0: unable to enumerate USB device on port 1
[ 649.908128] usb 2-2: new full speed USB device using uhci_hcd and address 18
[ 650.028107] usb 2-2: device descriptor read/64, error -71
[ 650.252164] usb 2-2: device descriptor read/64, error -71
[ 650.468173] usb 2-2: new full speed USB device using uhci_hcd and address 19
[ 650.592141] usb 2-2: device descriptor read/64, error -71
[ 650.816149] usb 2-2: device descriptor read/64, error -71
[ 651.088147] usb 2-2: new full speed USB device using uhci_hcd and address 20
[ 651.496158] usb 2-2: device not accepting address 20, error -71
[ 651.608145] usb 2-2: new full speed USB device using uhci_hcd and address 21
[ 652.016145] usb 2-2: device not accepting address 21, error -71
[ 652.016190] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 690.864177] usb 1-3: new high speed USB device using ehci_hcd and address 14
[ 691.046613] usb 1-3: configuration #1 chosen from 1 choice
[ 691.088732] scsi7 : SCSI emulation for USB Mass Storage devices
[ 691.091441] usb-storage: device found at 14
[ 691.091451] usb-storage: waiting for device to settle before scanning
[ 696.088317] usb-storage: device scan complete
[ 702.112086] usb 1-3: reset high speed USB device using ehci_hcd and address 14
[ 717.224062] usb 1-3: device descriptor read/64, error -110
[ 717.552440] scsi 7:0:0:0: Direct-Access General Hard Disk PQ: 0 ANSI: 2 CCS
[ 717.621538] sd 7:0:0:0: [sdc] Attached SCSI disk
[ 717.621728] sd 7:0:0:0: Attached scsi generic sg2 type 0
[ 725.761120] usb 1-3: USB disconnect, address 14
[ 731.296101] usb 1-3: new high speed USB device using ehci_hcd and address 15
[ 731.478358] usb 1-3: configuration #1 chosen from 1 choice
[ 731.519464] scsi8 : SCSI emulation for USB Mass Storage devices
[ 731.522835] usb-storage: device found at 15
[ 731.522844] usb-storage: waiting for device to settle before scanning
[ 736.520325] usb-storage: device scan complete
[ 736.591571] scsi 8:0:0:0: Direct-Access WDC WD32 00BEVT-11ZCT0 PQ: 0 ANSI: 2 CCS
[ 736.596132] sd 8:0:0:0: [sdc] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 736.643794] sd 8:0:0:0: [sdc] Write Protect is off
[ 736.643808] sd 8:0:0:0: [sdc] Mode Sense: 3c 00 00 00
[ 736.643815] sd 8:0:0:0: [sdc] Assuming drive cache: write through
[ 736.645951] sd 8:0:0:0: [sdc] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 736.647149] sd 8:0:0:0: [sdc] Write Protect is off
[ 736.647161] sd 8:0:0:0: [sdc] Mode Sense: 3c 00 00 00
[ 736.647168] sd 8:0:0:0: [sdc] Assuming drive cache: write through
[ 736.647186] sdc: sdc1
[ 736.699264] sd 8:0:0:0: [sdc] Attached SCSI disk
[ 736.699462] sd 8:0:0:0: Attached scsi generic sg2 type 0
[ 762.144134] usb 2-2: new full speed USB device using uhci_hcd and address 22
[ 762.324050] usb 2-2: device descriptor read/64, error -71
[ 762.552045] usb 2-2: device descriptor read/64, error -71
[ 762.768060] usb 2-2: new full speed USB device using uhci_hcd and address 23
[ 762.892115] usb 2-2: device descriptor read/64, error -71
[ 763.140117] usb 2-2: device descriptor read/64, error -71
[ 763.356048] usb 2-2: new full speed USB device using uhci_hcd and address 24
[ 763.772119] usb 2-2: device not accepting address 24, error -71
[ 763.884052] usb 2-2: new full speed USB device using uhci_hcd and address 25
[ 764.300051] usb 2-2: device not accepting address 25, error -71
[ 764.300097] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 908.176164] usb 2-2: new full speed USB device using uhci_hcd and address 26
[ 908.300185] usb 2-2: device descriptor read/64, error -71
[ 908.528125] usb 2-2: device descriptor read/64, error -71
[ 908.744157] usb 2-2: new full speed USB device using uhci_hcd and address 27
[ 908.868156] usb 2-2: device descriptor read/64, error -71
[ 909.096165] usb 2-2: device descriptor read/64, error -71
[ 909.312160] usb 2-2: new full speed USB device using uhci_hcd and address 28
[ 909.728177] usb 2-2: device not accepting address 28, error -71
[ 909.840177] usb 2-2: new full speed USB device using uhci_hcd and address 29
[ 910.256192] usb 2-2: device not accepting address 29, error -71
[ 910.256239] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 970.588062] hub 1-0:1.0: unable to enumerate USB device on port 2
[ 971.080123] usb 2-2: new low speed USB device using uhci_hcd and address 30
[ 971.296107] usb 2-2: configuration #1 chosen from 1 choice
[ 971.341805] usbcore: registered new interface driver hiddev
[ 971.355324] input: USB Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input10
[ 971.357035] generic-usb 0003:05E3:1205.0001: input,hidraw0: USB HID v1.10 Mouse [USB Mouse ] on usb-0000:00:1d.0-2/input0
[ 971.357105] usbcore: registered new interface driver usbhid
[ 971.357114] usbhid: v2.6:USB HID core driver
[ 1720.355627] [drm:i915_getparam] *ERROR* Unknown parameter 6
[ 9574.456139] usb 2-2: USB disconnect, address 30
[ 9581.308073] usb 2-2: new full speed USB device using uhci_hcd and address 31
[ 9581.428070] usb 2-2: device descriptor read/64, error -71
[ 9581.652078] usb 2-2: device descriptor read/64, error -71
[ 9581.868072] usb 2-2: new full speed USB device using uhci_hcd and address 32
[ 9581.988080] usb 2-2: device descriptor read/64, error -71
[ 9582.216048] usb 2-2: device descriptor read/64, error -71
[ 9582.432069] usb 2-2: new full speed USB device using uhci_hcd and address 33
[ 9582.840069] usb 2-2: device not accepting address 33, error -71
[ 9582.952072] usb 2-2: new full speed USB device using uhci_hcd and address 34
[ 9583.364072] usb 2-2: device not accepting address 34, error -71
[ 9583.364106] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 9615.654462] usb 1-3: USB disconnect, address 15
[ 9625.284060] usb 3-1: new full speed USB device using uhci_hcd and address 15
[ 9625.404058] usb 3-1: device descriptor read/64, error -71
[ 9625.628080] usb 3-1: device descriptor read/64, error -71
[ 9625.844054] usb 3-1: new full speed USB device using uhci_hcd and address 16
[ 9625.964053] usb 3-1: device descriptor read/64, error -71
[ 9626.188071] usb 3-1: device descriptor read/64, error -71
[ 9626.404100] usb 3-1: new full speed USB device using uhci_hcd and address 17
[ 9626.816066] usb 3-1: device not accepting address 17, error -71
[ 9626.928061] usb 3-1: new full speed USB device using uhci_hcd and address 18
[ 9627.340056] usb 3-1: device not accepting address 18, error -71
[ 9627.340095] hub 3-0:1.0: unable to enumerate USB device on port 1
[ 9666.580049] usb 3-1: new full speed USB device using uhci_hcd and address 19
[ 9666.700075] usb 3-1: device descriptor read/64, error -71
[ 9666.924080] usb 3-1: device descriptor read/64, error -71
[ 9667.140045] usb 3-1: new full speed USB device using uhci_hcd and address 20
[ 9667.260049] usb 3-1: device descriptor read/64, error -71
[ 9667.484046] usb 3-1: device descriptor read/64, error -71
[ 9667.700069] usb 3-1: new full speed USB device using uhci_hcd and address 21
[ 9668.112078] usb 3-1: device not accepting address 21, error -71
[ 9668.224064] usb 3-1: new full speed USB device using uhci_hcd and address 22
[ 9668.636050] usb 3-1: device not accepting address 22, error -71
[ 9668.636089] hub 3-0:1.0: unable to enumerate USB device on port 1
[ 9682.328109] usb 3-1: new full speed USB device using uhci_hcd and address 23
[ 9682.448146] usb 3-1: device descriptor read/64, error -71
[ 9682.672075] usb 3-1: device descriptor read/64, error -71
[ 9682.888076] usb 3-1: new full speed USB device using uhci_hcd and address 24
[ 9683.023116] usb 3-1: device descriptor read/64, error -71
[ 9683.244079] usb 3-1: device descriptor read/64, error -71
[ 9683.460090] usb 3-1: new full speed USB device using uhci_hcd and address 25
[ 9683.868045] usb 3-1: device not accepting address 25, error -71
[ 9683.980129] usb 3-1: new full speed USB device using uhci_hcd and address 26
[ 9684.388047] usb 3-1: device not accepting address 26, error -71
[ 9684.388092] hub 3-0:1.0: unable to enumerate USB device on port 1
[ 9701.476110] usb 3-1: new full speed USB device using uhci_hcd and address 27
[ 9701.600049] usb 3-1: device descriptor read/64, error -71
[ 9701.828108] usb 3-1: device descriptor read/64, error -71
[ 9702.044058] usb 3-1: new full speed USB device using uhci_hcd and address 28
[ 9702.168042] usb 3-1: device descriptor read/64, error -71
[ 9702.396112] usb 3-1: device descriptor read/64, error -71
[ 9702.612109] usb 3-1: new full speed USB device using uhci_hcd and address 29
[ 9703.028048] usb 3-1: device not accepting address 29, error -71
[ 9703.140062] usb 3-1: new full speed USB device using uhci_hcd and address 30
[ 9703.556054] usb 3-1: device not accepting address 30, error -71
[ 9703.556096] hub 3-0:1.0: unable to enumerate USB device on port 1
[ 9715.788172] usb 3-1: new full speed USB device using uhci_hcd and address 31
[ 9715.852209] hub 3-0:1.0: unable to enumerate USB device on port 1
[ 9716.320191] hub 1-0:1.0: unable to enumerate USB device on port 3
[ 9733.536064] usb 3-1: new full speed USB device using uhci_hcd and address 32
[ 9733.660056] usb 3-1: device descriptor read/64, error -71
[ 9733.888327] usb 3-1: device descriptor read/64, error -71
[ 9734.104057] usb 3-1: new full speed USB device using uhci_hcd and address 33
[ 9734.229936] usb 3-1: device descriptor read/64, error -71
[ 9734.456054] usb 3-1: device descriptor read/64, error -71
[ 9734.672057] usb 3-1: new full speed USB device using uhci_hcd and address 34
[ 9735.088047] usb 3-1: device not accepting address 34, error -71
[ 9735.200057] usb 3-1: new full speed USB device using uhci_hcd and address 35
[ 9735.616044] usb 3-1: device not accepting address 35, error -71
[ 9735.616084] hub 3-0:1.0: unable to enumerate USB device on port 1
[ 9757.640115] usb 1-3: new high speed USB device using ehci_hcd and address 30
[ 9757.821856] usb 1-3: configuration #1 chosen from 1 choice
[ 9757.863458] scsi9 : SCSI emulation for USB Mass Storage devices
[ 9757.866739] usb-storage: device found at 30
[ 9757.866749] usb-storage: waiting for device to settle before scanning
[ 9762.864340] usb-storage: device scan complete
[ 9762.935465] scsi 9:0:0:0: Direct-Access WDC WD32 00BEVT-11ZCT0 PQ: 0 ANSI: 2 CCS
[ 9762.940070] sd 9:0:0:0: [sdc] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 9762.987203] sd 9:0:0:0: [sdc] Write Protect is off
[ 9762.987217] sd 9:0:0:0: [sdc] Mode Sense: 3c 00 00 00
[ 9762.987225] sd 9:0:0:0: [sdc] Assuming drive cache: write through
[ 9762.989212] sd 9:0:0:0: [sdc] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 9762.990283] sd 9:0:0:0: [sdc] Write Protect is off
[ 9762.990294] sd 9:0:0:0: [sdc] Mode Sense: 3c 00 00 00
[ 9762.990302] sd 9:0:0:0: [sdc] Assuming drive cache: write through
[ 9762.990321] sdc: sdc1
[ 9763.031466] sd 9:0:0:0: [sdc] Attached SCSI disk
[ 9763.031663] sd 9:0:0:0: Attached scsi generic sg2 type 0
[ 9786.444194] usb 2-2: new low speed USB device using uhci_hcd and address 35
[ 9786.661081] usb 2-2: configuration #1 chosen from 1 choice
[ 9786.678422] input: USB Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input11
[ 9786.708361] generic-usb 0003:05E3:1205.0002: input,hidraw0: USB HID v1.10 Mouse [USB Mouse ] on usb-0000:00:1d.0-2/input0
jaanus@jaanus:~$
vabandan et niimoodi kopi paste tegin, ma praegu ei osanud leida kuidas seda juttu sinna kasti sisse saab, pole ammu foorumis olnud

Postitatud: **15.12.2009, 09:16**

samsungime kirjutas:proovisin jälle oma vana ketast ühendada, ei saanud, nüüd uus ketas taga kerneli logi annab sellise jutu,
[..]
[ 78.448133] usb 3-2: new full speed USB device using uhci_hcd and address 2
[ 78.591957] usb 3-2: not running at top speed; connect to a high speed hub
[ 78.622753] usb 3-2: configuration #1 chosen from 1 choice
[ 78.643416] scsi3 : SCSI emulation for USB Mass Storage devices
[ 78.661007] usb-storage: device found at 2
[ 78.661016] usb-storage: waiting for device to settle before scanning
[ 83.662065] usb-storage: device scan complete
[ 83.665083] scsi 3:0:0:0: Direct-Access WD 1600BEV External 1.04 PQ: 0 ANSI: 4
[ 83.719045] sd 3:0:0:0: [sdc] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
[ 83.724128] sd 3:0:0:0: [sdc] Write Protect is off
[ 83.724141] sd 3:0:0:0: [sdc] Mode Sense: 21 00 00 00
[ 83.724149] sd 3:0:0:0: [sdc] Assuming drive cache: write through
[ 83.729207] sd 3:0:0:0: [sdc] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
[ 83.734219] sd 3:0:0:0: [sdc] Write Protect is off
[ 83.734232] sd 3:0:0:0: [sdc] Mode Sense: 21 00 00 00
[ 83.734240] sd 3:0:0:0: [sdc] Assuming drive cache: write through
[ 83.734261] sdc: sdc1
[ 83.797091] sd 3:0:0:0: [sdc] Attached SCSI disk
[ 83.797291] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 145.820079] usb 3-2: reset full speed USB device using uhci_hcd and address 2

Ketas WD 1600BEV sai külge ja tunti ära.

[ 145.940087] usb 3-2: device descriptor read/64, error -71
[ 146.164074] usb 3-2: device descriptor read/64, error -71
[ 146.380057] usb 3-2: reset full speed USB device using uhci_hcd and address 2
[ 146.516050] usb 3-2: device descriptor read/64, error -71
[ 146.765578] usb 3-2: device descriptor read/64, error -71
[ 146.980044] usb 3-2: reset full speed USB device using uhci_hcd and address 2
[ 147.388024] usb 3-2: device not accepting address 2, error -71
[ 147.500033] usb 3-2: reset full speed USB device using uhci_hcd and address 2
[ 147.908027] usb 3-2: device not accepting address 2, error -71
[ 147.908191] sd 3:0:0:0: [sdc] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[ 147.908205] end_request: I/O error, dev sdc, sector 0
[ 147.908216] Buffer I/O error on device sdc, logical block 0
[ 147.908232] Buffer I/O error on device sdc, logical block 1
[ 147.908240] Buffer I/O error on device sdc, logical block 2
[ 147.908248] Buffer I/O error on device sdc, logical block 3
[ 147.908373] usb 3-2: USB disconnect, address 2

Vead kettalt lugemisel, loobus.
Proovisid vist paar korda veel, ikka sama lugu.

Nüüd ühendasid uue välise ketta (WDC WD32 00BEVT-11ZCT0).

[ 9757.640115] usb 1-3: new high speed USB device using ehci_hcd and address 30
[ 9757.821856] usb 1-3: configuration #1 chosen from 1 choice
[ 9757.863458] scsi9 : SCSI emulation for USB Mass Storage devices
[ 9757.866739] usb-storage: device found at 30
[ 9757.866749] usb-storage: waiting for device to settle before scanning
[ 9762.864340] usb-storage: device scan complete
[ 9762.935465] scsi 9:0:0:0: Direct-Access WDC WD32 00BEVT-11ZCT0 PQ: 0 ANSI: 2 CCS
[ 9762.940070] sd 9:0:0:0: [sdc] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 9762.987203] sd 9:0:0:0: [sdc] Write Protect is off
[ 9762.987217] sd 9:0:0:0: [sdc] Mode Sense: 3c 00 00 00
[ 9762.987225] sd 9:0:0:0: [sdc] Assuming drive cache: write through
[ 9762.989212] sd 9:0:0:0: [sdc] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 9762.990283] sd 9:0:0:0: [sdc] Write Protect is off
[ 9762.990294] sd 9:0:0:0: [sdc] Mode Sense: 3c 00 00 00
[ 9762.990302] sd 9:0:0:0: [sdc] Assuming drive cache: write through
[ 9762.990321] sdc: sdc1
[ 9763.031466] sd 9:0:0:0: [sdc] Attached SCSI disk
[ 9763.031663] sd 9:0:0:0: Attached scsi generic sg2 type 0
[ 9786.444194] usb 2-2: new low speed USB device using uhci_hcd and address 35
[ 9786.661081] usb 2-2: configuration #1 chosen from 1 choice
[ 9786.678422] input: USB Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input11
[ 9786.708361] generic-usb 0003:05E3:1205.0002: input,hidraw0: USB HID v1.10 Mouse [USB Mouse ] on usb-0000:00:1d.0-2/input0

See läks kenasti käima.

Postitatud: **15.12.2009, 12:57**

Normaalse syntaxi toe võiks ka siia foorumisse lisada või vähemalt see pikk tekst panna.

Kood: Vali kõik

Postitatud: **15.12.2009, 13:27**

koodi saad kasti sisse panna
# nupuga kui teksti sisestad!

Lepi sellega, et sa selle vana ketta oled lõplikult peesse keeranud ja sul ei ole sellega midagi teha... Kauta uut ketast, ning hoia seda...
PS sulle teadmiseks, et kettad kardavad niiskust, põrutusi, koputusi, staatilist elektrit ja on väga õrnad asjad... See paljalt tasku pistmine on ka üks surm kettale, eriti kui kannad palju sünteetilisest materjalist riideid

Pingviini veeb

Probleem välise kõvakettaga

Probleem välise kõvakettaga