Digi tv linuxis

Kaar3l · Postitus Postitas **Kaar3l** » 10.11.2010, 21:16

Asi pole KINDLASTI firmware puudumises. See kasutab mingit uut RTL2832U kiipi ja sellele on mingi tugi olemas juba.

http://www.mail-archive.com/linux-media ... 16452.html
Selle asja järgi tehes võib asja saada.

EDIT:
Tegin selle õpetuse järgi ja sain asja kompilleeritud ka. Lasin upload.ee-sse asja üles, saad proovida.

http://www.upload.ee/files/916675/rtl2832u.tar.gz.html
Kindlasti
sudo apt-get install build-essential
Siis paki lahti see ja seal kataloogis:
make
ja kui kõik läheb hästi siis:
sudo make install

restart ja pulka proovima

illukas · Postitus Postitas **illukas** » 10.11.2010, 22:18

aga tee deb

Kaar3l · Postitus Postitas **Kaar3l** » 10.11.2010, 23:16

Ma ei tea kas see toimib ka

aga siin ta on (minu esimene deb pakike):
http://www.upload.ee/files/916902/rtl28 ... 4.deb.html
See on mul 64 peal kompilleeritud, kui 32 peal tahad installida, siis ma soovitaks kompilleerida, on kindlam.

GreyShark · Postitus Postitas **GreyShark** » 11.11.2010, 17:20

to Kaar3l

Tegin nagu õpetuses kirjas oli aga sain errori:

allan@allan-laptop:~/Töölaud/rtl2832u$ sudo make
make -C /home/allan/Töölaud/rtl2832u/v4l
make[1]: Entering directory `/home/allan/Töölaud/rtl2832u/v4l'
perl scripts/make_config_compat.pl /lib/modules/2.6.32-21-generic/build ./.myconfig ./config-compat.h
File not found: /lib/modules/2.6.32-21-generic/build/include/linux/netdevice.h at scripts/make_config_compat.pl line 15.
make[1]: *** [config-compat.h] Error 2
make[1]: Leaving directory `/home/allan/Töölaud/rtl2832u/v4l'
make: *** [all] Error 2

Milles viga?

Postitus Postitas **sander85** » 11.11.2010, 17:33

sul on kerneli devel failid puudu vast, aga mis pakis need buntul paiknevad, seda teavad buntu inimesed..

GreyShark · Postitus Postitas **GreyShark** » 11.11.2010, 17:48

Kuidas ma need devel failid kätte siis saaks?

-ordi- · Postitus Postitas **-ordi-** » 11.11.2010, 17:57

GreyShark kirjutas:Kuidas ma need devel failid kätte siis saaks?

sudo apt-get install build-essential

GreyShark · Postitus Postitas **GreyShark** » 11.11.2010, 18:00

sudo apt-get install build-essential

Enne kompileerimise algust installisin ära...
Kas pean arvutile restardi tegema?

-ordi- · Postitus Postitas **-ordi-** » 11.11.2010, 18:23

GreyShark kirjutas:sudo apt-get install build-essential

Enne kompileerimise algust installisin ära...
Kas pean arvutile restardi tegema?

Võimalik et on veel mõni sõltuvus puudu (vt README faili vms, seal peaks olema mida vaja ja mida mitte).

GreyShark · Postitus Postitas **GreyShark** » 11.11.2010, 19:09

readme failis ka mingeid sõltuvusi välja ei pakkuta...

Kaar3l · Postitus Postitas **Kaar3l** » 11.11.2010, 19:23

Kontrolli kas linux-headers-2.6.X.Y on peale lastud, enda kerneli oma siis. Siis veel gcc.

See laseb veel head paremat peale:

Kood: Vali kõik

sudo apt-get install checkinstall build-essential cmake libtool automake autoconf git-core ffmpeg libxcb-shm0-dev libxcb-xv0-dev libx11-xcb-dev libcdparanoia-dev libcdio-paranoia-dev libcdio-cdda-dev libqt4-dev qt4-dev-tools qt4-qmake nasm yasm libasm-dev lua5.1

GreyShark · Postitus Postitas **GreyShark** » 11.11.2010, 19:35

On vaja tõmmata 97,8MB arhiive.
Selle tegevuse tulemusel kasutatakse 182MB lisa kettaruumi.

Vaatan jah et mõned pakketid puudu. Ma tõmban muidu homme ära ja kui probleeme tekkib siis kirjutan siia uuesti.

linux-headers-2.6.X.Y
Praegu siis siukene kernel peal: 2.6.32-25-generic

Kaar3l · Postitus Postitas **Kaar3l** » 11.11.2010, 20:11

Siis peaks toimima:
linux-headers-2.6.32-25

GreyShark · Postitus Postitas **GreyShark** » 12.11.2010, 13:54

Paigaldasin peale kõik pakid mis kaar3l andis aga ikka saan errori:

allan@allan-laptop:~/Töölaud/rtl2832u$ make
make -C /home/allan/Töölaud/rtl2832u/v4l
make[1]: Entering directory `/home/allan/Töölaud/rtl2832u/v4l'
perl scripts/make_config_compat.pl /lib/modules/2.6.32-21-generic/build ./.myconfig ./config-compat.h
File not found: /lib/modules/2.6.32-21-generic/build/include/linux/netdevice.h at scripts/make_config_compat.pl line 15.
make[1]: *** [config-compat.h] Error 2
make[1]: Leaving directory `/home/allan/Töölaud/rtl2832u/v4l'
make: *** [all] Error 2

Kaar3l · Postitus Postitas **Kaar3l** » 12.11.2010, 14:07

Proovi:
make distclean
siis pane make
ning oota nii 5 seki ja Ctrl+C
Seejärel mine v4l kataloogi ja otsi fail nimega(peidetud failid nähtavaks Ctrl+H):
.config
Seal failis otsi rida:
CONFIG_DVB_FIREDTV=m
ja muuda:
CONFIG_DVB_FIREDTV=n
Seejärel pane make ja siis peaks asi sujuma.

EDIT

Tegin 32-bit deb paki ka:
http://www.upload.ee/files/919343/rtl28 ... 6.deb.html

GreyShark · Postitus Postitas **GreyShark** » 12.11.2010, 16:08

Kompileerisin ära ilusti. Ühtegi errorit ei näinud kompileerimise ja paigaldamise ajal. Tegin restardi ära aga me tv ikka ei tunne fujitsu seadet ära...

Kaar3l · Postitus Postitas **Kaar3l** » 12.11.2010, 16:18

Mis dmesg näitab?

GreyShark · Postitus Postitas **GreyShark** » 12.11.2010, 16:32

ei hakka tervet ülesse panema. Panen ainult viimased read:

[ 25.368517] eth0: link down
[ 25.368898] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 25.372854] type=1505 audit(1289570232.338:14): operation="profile_load" pid=774 name="/usr/sbin/tcpdump"
[ 34.964843] ppdev: user-space parallel port driver
[ 78.465324] ndiswrapper (iw_set_auth:1602): invalid cmd 12
[ 79.000310] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 89.588044] wlan0: no IPv6 routers present
[ 92.828063] usb 1-6: new high speed USB device using ehci_hcd and address 2
[ 92.972300] usb 1-6: configuration #1 chosen from 1 choice
[ 189.508402] lo: Disabled Privacy Extensions
[ 539.018078] usb 1-6: USB disconnect, address 2
[ 542.792069] usb 1-6: new high speed USB device using ehci_hcd and address 3
[ 542.936393] usb 1-6: configuration #1 chosen from 1 choice
[ 564.906274] usb 1-6: USB disconnect, address 3
[ 570.848094] usb 1-6: new high speed USB device using ehci_hcd and address 4
[ 570.992347] usb 1-6: configuration #1 chosen from 1 choice
[ 1841.312937] lo: Disabled Privacy Extensions
[ 1986.076157] lo: Disabled Privacy Extensions
[ 2010.320491] usb 1-6: USB disconnect, address 4
[ 2020.244245] usb 1-6: new high speed USB device using ehci_hcd and address 5
[ 2020.388511] usb 1-6: configuration #1 chosen from 1 choice

-ordi- · Postitus Postitas **-ordi-** » 12.11.2010, 16:47

GreyShark kirjutas:ei hakka tervet ülesse panema. Panen ainult viimased read:

[ 25.368517] eth0: link down
[ 25.368898] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 25.372854] type=1505 audit(1289570232.338:14): operation="profile_load" pid=774 name="/usr/sbin/tcpdump"
[ 34.964843] ppdev: user-space parallel port driver
[ 78.465324] ndiswrapper (iw_set_auth:1602): invalid cmd 12
[ 79.000310] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 89.588044] wlan0: no IPv6 routers present
[ 92.828063] usb 1-6: new high speed USB device using ehci_hcd and address 2
[ 92.972300] usb 1-6: configuration #1 chosen from 1 choice
[ 189.508402] lo: Disabled Privacy Extensions
[ 539.018078] usb 1-6: USB disconnect, address 2
[ 542.792069] usb 1-6: new high speed USB device using ehci_hcd and address 3
[ 542.936393] usb 1-6: configuration #1 chosen from 1 choice
[ 564.906274] usb 1-6: USB disconnect, address 3
[ 570.848094] usb 1-6: new high speed USB device using ehci_hcd and address 4
[ 570.992347] usb 1-6: configuration #1 chosen from 1 choice
[ 1841.312937] lo: Disabled Privacy Extensions
[ 1986.076157] lo: Disabled Privacy Extensions
[ 2010.320491] usb 1-6: USB disconnect, address 4
[ 2020.244245] usb 1-6: new high speed USB device using ehci_hcd and address 5
[ 2020.388511] usb 1-6: configuration #1 chosen from 1 choice

sudo make install tegid?

Kaar3l · Postitus Postitas **Kaar3l** » 12.11.2010, 17:20

Leidsin uuema driveri kompilleerisin ära tegin debi:
http://www.upload.ee/files/919528/v4l-d ... 6.deb.html