smartctl 5.42 2011-10-20 r3458 [x86_64-linux-3.4.6-2.10-desktop] (SUSE RPM)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model:     Hitachi HDS721010DLE630
Serial Number:    MSE5235V0J5KPL
LU WWN Device Id: 5 000cca 37cc75ad9
Firmware Version: MS2OA5R0
User Capacity:    1,000,204,886,016 bytes [1.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   8
ATA Standard is:  ATA-8-ACS revision 4
Local Time is:    Tue Jan  6 23:37:05 2015 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x85)	Offline data collection activity
					was aborted by an interrupting command from host.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      ( 117)	The previous self-test completed having
					the read element of the test failed.
Total time to complete Offline 
data collection: 		( 7313) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 122) minutes.
SCT capabilities: 	       (0x003d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     PO-R--   100   100   016    -    0
  2 Throughput_Performance  P-S---   100   100   054    -    273
  3 Spin_Up_Time            POS---   107   107   024    -    212 (Average 214)
  4 Start_Stop_Count        -O--C-   100   100   000    -    1677
  5 Reallocated_Sector_Ct   PO--CK   100   100   005    -    2
  7 Seek_Error_Rate         PO-R--   100   100   067    -    0
  8 Seek_Time_Performance   P-S---   115   115   020    -    34
  9 Power_On_Hours          -O--C-   100   100   000    -    4212
 10 Spin_Retry_Count        PO--C-   100   100   060    -    0
 12 Power_Cycle_Count       -O--CK   100   100   000    -    1677
192 Power-Off_Retract_Count -O--CK   099   099   000    -    1677
193 Load_Cycle_Count        -O--C-   099   099   000    -    1677
194 Temperature_Celsius     -O----   193   193   000    -    31 (Min/Max 10/43)
196 Reallocated_Event_Count -O--CK   100   100   000    -    3
197 Current_Pending_Sector  -O---K   100   100   000    -    16
198 Offline_Uncorrectable   ---R--   100   100   000    -    0
199 UDMA_CRC_Error_Count    -O-R--   200   200   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
GP/S  Log at address 0x00 has    1 sectors [Log Directory]
SMART Log at address 0x01 has    1 sectors [Summary SMART error log]
GP    Log at address 0x03 has    1 sectors [Ext. Comprehensive SMART error log]
GP    Log at address 0x04 has    7 sectors [Device Statistics log]
SMART Log at address 0x06 has    1 sectors [SMART self-test log]
GP    Log at address 0x07 has    1 sectors [Extended self-test log]
GP    Log at address 0x08 has    2 sectors [Power Conditions log]
SMART Log at address 0x09 has    1 sectors [Selective self-test log]
GP    Log at address 0x10 has    1 sectors [NCQ Command Error log]
GP    Log at address 0x11 has    1 sectors [SATA Phy Event Counters]
GP    Log at address 0x20 has    1 sectors [Streaming performance log]
GP    Log at address 0x21 has    1 sectors [Write stream error log]
GP    Log at address 0x22 has    1 sectors [Read stream error log]
GP/S  Log at address 0x80 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x81 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x82 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x83 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x84 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x85 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x86 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x87 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x88 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x89 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x8a has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x8b has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x8c has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x8d has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x8e has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x8f has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x90 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x91 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x92 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x93 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x94 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x95 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x96 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x97 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x98 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x99 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x9a has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x9b has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x9c has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x9d has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x9e has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x9f has   16 sectors [Host vendor specific log]
GP/S  Log at address 0xe0 has    1 sectors [SCT Command/Status]
GP/S  Log at address 0xe1 has    1 sectors [SCT Data Transfer]

SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Device Error Count: 400 (device log contains only the most recent 4 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 400 [3] occurred at disk power-on lifetime: 4211 hours (175 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 08 00 00 02 cd f5 68 02 00  Error: UNC at LBA = 0x02cdf568 = 47052136

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 00 00 00 02 cd f5 68 40 08     02:34:13.634  READ FPDMA QUEUED
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     02:34:13.634  SET FEATURES [Reserved for Serial ATA]
  27 00 00 00 00 00 00 00 00 00 00 e0 08     02:34:13.634  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     02:34:13.633  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 08     02:34:13.633  SET FEATURES [Set transfer mode]

Error 399 [2] occurred at disk power-on lifetime: 4211 hours (175 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 08 00 00 02 cd f5 68 02 00  Error: UNC at LBA = 0x02cdf568 = 47052136

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 00 00 00 02 cd f5 68 40 08     02:34:10.455  READ FPDMA QUEUED
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     02:34:10.455  SET FEATURES [Reserved for Serial ATA]
  27 00 00 00 00 00 00 00 00 00 00 e0 08     02:34:10.455  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     02:34:10.454  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 08     02:34:10.454  SET FEATURES [Set transfer mode]

Error 398 [1] occurred at disk power-on lifetime: 4211 hours (175 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 08 00 00 02 cd f5 68 02 00  Error: UNC at LBA = 0x02cdf568 = 47052136

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 00 00 00 02 cd f5 68 40 08     02:34:07.276  READ FPDMA QUEUED
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     02:34:07.276  SET FEATURES [Reserved for Serial ATA]
  27 00 00 00 00 00 00 00 00 00 00 e0 08     02:34:07.276  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     02:34:07.275  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 08     02:34:07.275  SET FEATURES [Set transfer mode]

Error 397 [0] occurred at disk power-on lifetime: 4211 hours (175 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 08 00 00 02 cd f5 68 02 00  Error: UNC at LBA = 0x02cdf568 = 47052136

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 00 00 00 02 cd f5 68 40 08     02:34:04.098  READ FPDMA QUEUED
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     02:34:04.097  SET FEATURES [Reserved for Serial ATA]
  27 00 00 00 00 00 00 00 00 00 00 e0 08     02:34:04.097  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     02:34:04.097  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 08     02:34:04.096  SET FEATURES [Set transfer mode]

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed: read failure       50%      4212         281432

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       256 (0x0100)
SCT Support Level:                   1
Device State:                        Active (0)
Current Temperature:                    31 Celsius
Power Cycle Min/Max Temperature:     22/33 Celsius
Lifetime    Min/Max Temperature:     10/43 Celsius
Under/Over Temperature Limit Count:   0/0
SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/60 Celsius
Min/Max Temperature Limit:           -40/70 Celsius
Temperature History Size (Index):    128 (55)

Index    Estimated Time   Temperature Celsius
  56    2015-01-06 21:30    29  **********
 ...    ..( 17 skipped).    ..  **********
  74    2015-01-06 21:48    29  **********
  75    2015-01-06 21:49    30  ***********
 ...    ..( 19 skipped).    ..  ***********
  95    2015-01-06 22:09    30  ***********
  96    2015-01-06 22:10    29  **********
 ...    ..(  2 skipped).    ..  **********
  99    2015-01-06 22:13    29  **********
 100    2015-01-06 22:14    30  ***********
 101    2015-01-06 22:15    30  ***********
 102    2015-01-06 22:16    29  **********
 103    2015-01-06 22:17    29  **********
 104    2015-01-06 22:18    29  **********
 105    2015-01-06 22:19    30  ***********
 106    2015-01-06 22:20    30  ***********
 107    2015-01-06 22:21    29  **********
 ...    ..(  5 skipped).    ..  **********
 113    2015-01-06 22:27    29  **********
 114    2015-01-06 22:28    30  ***********
 115    2015-01-06 22:29    29  **********
 116    2015-01-06 22:30    30  ***********
 ...    ..( 28 skipped).    ..  ***********
  17    2015-01-06 22:59    30  ***********
  18    2015-01-06 23:00    31  ************
 ...    ..(  3 skipped).    ..  ************
  22    2015-01-06 23:04    31  ************
  23    2015-01-06 23:05    32  *************
 ...    ..( 12 skipped).    ..  *************
  36    2015-01-06 23:18    32  *************
  37    2015-01-06 23:19    33  **************
 ...    ..(  8 skipped).    ..  **************
  46    2015-01-06 23:28    33  **************
  47    2015-01-06 23:29    32  *************
 ...    ..(  2 skipped).    ..  *************
  50    2015-01-06 23:32    32  *************
  51    2015-01-06 23:33    31  ************
  52    2015-01-06 23:34    32  *************
  53    2015-01-06 23:35    32  *************
  54    2015-01-06 23:36    31  ************
  55    2015-01-06 23:37    31  ************

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0009  2           59  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2           54  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS

